| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| The following commands were entered at the command prompt of a
Cisco router. What do they accomplish?
access-list 1000 deny 9e.1234.5678.1212 4
access-list 1000 permit -1
interface ethernet 0
ipx network 9e
interface ethernet 1
ipx network 4a
interface serial 0
ipx network 1
ipx output-sap-filter 1000
A. File server advertisements from server 9e.1234.5678.1212
will not be
forwarded on interface S0.
B. All other SAP services, other than file server, from any
source will
be forwarded on S0.
C. All other SAP services, other than print server, from any
source will
be forwarded on S0.
D. Print server advertisements from server 9e.1234.5678.1212
will not be
forwarded on interface S0. | | 1 |
| What is the regional telco office called, where the customers
local loop terminates?
A.) Demarc
B.) DTE
C.) DCE
D.) CO
E.) CPE | | 1 |
| Which layer is responsible for determining if sufficient
resources
for the intended communication exists?
A.) Application
B.) Network
C.) Session
D.) Presentation
E.) Transport | | 1 |
| Which network mask should you place on a Class C address to
accommodate a user requirement for five networks with a
maximum of 17 hosts on each networks
A. 255.255.255.192
B. 255.255.255.224
C. 255.255.255.240
D. 255.255.255.248 | | 7 |
| Most routing protocols recognize that it is never useful to send
information about a route back out the direction from which
the original
packet came. This is an example of which routing technology?
A.) Split Horizon
B.) LMI
C.) Triggered Updates
D.) Poison Reverse
E.) SYN, ACK
F.) DLCI | | 1 |
| Identify the command to determine if an IP access-list is
grouped
on interface e0?
A.) Router(config)# show ip interface e0
B.) Router> show ip interface e0
C.) Router# show interface e0
D.) Router# show ip interface e0 | | 1 |
| What is the protocol number for TCP?
A.) 80
B.) 21
C.) 11
D.) 6 | | 1 |
| What is the default interval for SAP updates?
A.) 60 seconds
B.) 15 seconds
C.) 30 seconds
D.) 120 seconds | ACS | 1 |
| Which statement is true regarding full duplex?
A.) Allows for transmission and receiving of data simultaneously
B.) Only works in a multipoint configuration
C.) Does not affect the bandwidth
D.) Allows for transmission and receiving of data but not a
the same time | | 2 |
| Identify 1 characteristic of RARP?
A.) MAC to IP address translation
B.) Connectionless delivery of packets
C.) Can be used to initiate remote O/S load sequence
D.) Generates error and control messages | | 3 |
| Identify the 2 rules used when configuring a Distance Vector
routing
protocol?
A.) Physically connected network(s)
B.) Configure the classfull address, no subnets
C.) Enable CDP so neighbors can be detected
D.) Same autonomous network | | 1 |
| Which range of possible numbers do standard ipx access lists
have?
A. 100 199
B. 600 699
C. 800 899
D. 1000-1099 | | 1 |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| Which OSI layer defines end to end communication,
segmentation and
re-assembly?
A.) Network
B.) Transport
C.) Physical
D.) Application
E.) Data-Link
F.) Presentation | | 1 |
| Why would you use static routing instead of dynamic routing?
A.) When you want automatic updates of the routing tables
B.) All the time
C.) When you have very few routes and want to conserve bandwidth
D.) When you have a gateway of last resort | | 1 |
| The CSMA/CD Ethernet IEEE committee is defined as which of the
following?
A.) 802.2
B.) 802.3
C.) 802.4
D.) 802.5 | | 1 |
| what is flow control,. | | 4 |
| Can anyone explain the STP Security features. Just like BPDU
guard, Root Guard.
Hi JITENDERA, i m specially looking for u????? | | 2 |
| The network portion of an address typically represents a:
A.) Router
B.) Ethernet MAC address.
C.) Computer
D.) Host
E.) Segment | | 2 |
| How do you get help on a command after you have received the
% incomplete command response from a switch CLI?
A. type "history" to review the prompt before the error
B. enter a question mark to display all the console commands
C. type help followed by the command to see command parameters
D. reenter the command followed by a question mark to view
keywords | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
