| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which OSI layer handles physical address, network topology?
A.) Presentation
B.) Physical
C.) Transport
D.) Application
E.) Data-Link
F.) Network | | 1 |
| Which command will display the encapsulation type on interface
serial 0?
A.) show interface s0
B.) show all
C.) show int s0 encap
D.) show encap s0
E.) show encap | | 1 |
| What is a back off on an 802.3 networks?
A. It is latency in store and forward switching
B. It is the time used for token passing from machine to machine
C. It is the retransmission delay that is enforced when a
collision occurs
D. It is the result of two nodes transmitting at the same
time. The frames from each transmitting device collide and
are damaged | | 1 |
| Given the command 'cl?', what will it display?
A.) Syntax of the 'clock' command
B.) Syntax of the 'clear' command
C.) All commands that begin with 'cl'
D.) All commands that begin with 'c' | | 2 |
| Which IP host address range is allowable given an IP address
of 172.37.2.56 and 12 bits of subnetting
A. 172.37.2.48 to 172.37.2.63
B. 172.37.2.48 to 172.37.2.62
C. 172.37.2.49 to 172.37.2.62
D. 172.37.2.49 to 172.37.2.63
E. 172.37.2.55 to 172.37.2.126 | | 1 |
| Which configuration task must you complete if a remote Frame
Relay router does NOT support Inverse APP?
A.configure static maps
B.define an IP address locally
C.disable DHCP on the Frame Relay router
D.configure a static route to the remote network | | 1 |
| What is the IP extended access list range?
A.) 1000-1099
B.) 100-199
C.) 1-99
D.) 101-200 | | 2 |
| How do you set the encapsulation type to PPP for an interface?
A.) encap ppp
B.) ppp encapsulation
C.) encapsulation ppp
D.) encapsulation ppp enable
E.) ppp enable encapsulation | | 2 |
| What does a Standard IP Access-list use as test criteria?
A.) IP source address
B.) IP source and destination address, protocol numbers and
port numbers
C.) IPX source and destination address
D.) Source MAC address | | 1 |
| You have just issued the erase startup-config Command and
reloaded your router. In which mode will your router be
when you react?
A. setup
B. startup
C. user EXEC
D. userd privileged
E. global configuration | | 2 |
| How we put NIC in promiscuous mode when using MS windows,
can any one tell me in detail | Cisco | 1 |
| If you are in IOS user mode, which command do you use to
enter the privileged mode?
A. Set
B. Enable
C. Configure
D. Privileges | | 1 |
| What is an example of a valid MAC address?
A. 192.201.63.251
B. 19-22-01-63-25
C. 0000.1234.FEGA
D. 00.00.12.34.FE.AA | Aricent | 3 |
| When setting up a frame-relay network between a Cisco router
and a
non-Cisco router, what encapsulation type should you use?
A.) SAP
B.) CISCO
C.) IANA
D.) Apollo
E.) IETF
F.) Q933A | | 1 |
| Identify 3 UDP characteristics?
A.) Reliable communication protocol
B.) Applications that use UDP must incorporate reliability
C.) Connnection-less oriented
D.) Incorporates no handshaking | | 2 |
| Which two of the following are valid ways to have multiple
encapsulation types on a single interface?
A.) This is not possible
B.) subinterfaces
C.) additional physical interfaces
D.) secondary addresses | | 2 |
| What is the Function of Layer3 Switch? | | 1 |
| Identify the type of hardware required to connect a Token ring
network to an Ethernet network?
A.) Repeater
B.) TR-Enet
C.) Router
D.) Token Ring to Ethernet translation hub | | 1 |
| Which layer is responsible for negotiating data transfer syntax?
A.) Network
B.) Session
C.) Application
D.) Transport
E.) Presentation | | 1 |
| When would you use ISDN?
A.) To connect LANs using POTS
B.) To support applications requiring voice, data, and video
C.) When you need a consistent and very high rate of data speed
D.) To connect to IBM mainframes | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
