| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following provide connection-oriented transport
to upper
layer protocols?
A.) SPX
B.) RIP
C.) NLSP
D.) NCP | | 1 |
| What is the function of Layer 2 Switch? | | 1 |
| What is the default switching method for the Cisco 5000 series?
A.) Cut-through
B.) Store-and-splice
C.) Latency
D.) Store-and-forward | | 1 |
| WAN stands for which of the following?
A.) Wide Arena Network
B.) World Area Network
C.) Wide Area News
D.) Wide Area Network | | 1 |
| What is the result of using a hierarchical addressing framework?
A. increased availability of addresses
B. decreased distance between routers
C. increased router memory requirements
D. no need to maintain routing information | | 2 |
| What are two functions of the ICMP protocol? (Choose two)
A. to map IP addresses to Ethernet addresses
B. to map common names to network addresses
C. to forward SNMP alerts to management consoles
D. to generate an echo reply in response to a ping test
E. to send a host or pod unreachable message from a router
to the source of an undeliverable packet | | 1 |
| Hi, Shahin
Thanks a lot for providing me these sites. These links are
really helpful for me. r u working somewhere please let me
know | | 1 |
| What does a router do with a packet that it does not have a
destination
network for?
A.) Sends it to the Serial port
B.) Drops the packet
C.) Sends it back out the same interface it received it in
D.) Forwards the packet to the next hop | | 1 |
| Identify the command mode necessary to enter the standard ping
command?
A.) Router(config)#
B.) Router>
C.) Router(std-ping)#
D.) Router(config-if)# | | 2 |
| Which two protocol tools use ICMP? (Choose two)
A. ping
B. telnet
C. configure
D. traceroute
E. show commands
F. standard access lists | | 3 |
| How does the cut-through switching technique work?
A.) By using broadcast address as source addresses
B.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets
C.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
D.) By using a Class I repeater in a collision domain | | 3 |
| In order to configure a Frame Relay subinterface with IP
identify
the 2 commands that must be configured on the physcial
interface?
A.) Router(config-if)# encapsulation frame-relay
B.) Router(config-if)# no ip address
C.) Router(config-if)#encapsulation subinterface frame-relay
D.) Router(config)# subinterface s0 encapsulation frame-relay | | 2 |
| Which network mask should you place on a Class C address to
accommodate a user requirement of two subnetworks with a
maxximum of 35 hosts on each networks
A. 255.255.255.192
B. 255.255.255.224
C. 255.255.255.240
D. 255.255.255.248 | | 4 |
| Identify 3 IP routing protocols?
A.) RIP
B.) AURP
C.) OSPF
D.) IGRP
E.) ARP
F.) ICMP | | 2 |
| The Internet Control Message Protocol occurs at what layer
of the
seven layer model?
A.) Physical
B.) Transport
C.) Session
D.) Datalink
E.) Presentation
F.) Network | | 2 |
| Using the access-list command, 'access-list 1 deny 2.2.2.2',
what
else must be done to stop host 2.2.2.2 from sending any
traffic out of
physical interface E0,
while still allowing other traffic?
A.) In global mode, Add a line - 'access-list 1 permit
0.0.0.0 255.255.255.255'
B.) On interface E0, Add a line - 'access-group 1 in'
C.) In global mode, Add a line - 'access-list 1 permit all'
D.) On interface E0, Add a line - 'access-list 1 in'
E.) On interface E0, Add a line - 'access-list 1 out'
F.) On interface E0, Add a line - 'ip access-group 1' | | 1 |
| What is a back off on an 802.3 networks?
A. It is latency in store and forward switching
B. It is the time used for token passing from machine to machine
C. It is the retransmission delay that is enforced when a
collision occurs
D. It is the result of two nodes transmitting at the same
time. The frames from each transmitting device collide and
are damaged | | 1 |
| What key do you use to view the last command?
A.) Ctrl+X
B.) Ctrl+Z
C.) Ctrl+E
D.) Ctrl+P | | 1 |
| Which two of the following protocols are used at the
Transport layer?
A.) ARP
B.) UDP
C.) ICMP
D.) RARP
E.) TCP
F.) BootP | | 1 |
| Which processes does TCP, but not UDP, use?
A. Windowing
B. Acknowledgements
C. Source Port
D. Destination Port | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
