| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which two does 100BaseT use?
A.) CSMA/CD
B.) IEEE 802.5
C.) 802.3u
D.) Switching with 53-byte cells | | 1 |
| How do you disable advanced editing?
A.) terminal editing
B.) terminal no editing
C.) disable editing
D.) no terminal editing | | 2 |
| On an ISDN BRI interface, the control channel is the 'D'
channel.
What is the rate of this channel?
A.) 64 Kbps
B.) 1.544 Mbps
C.) 128 Kbps
D.) 2.048 Mbps
E.) 16 Kbps | | 4 |
| Identify the default values that make up IGRP's composite
metric?
A.) Bandwidth
B.) Load
C.) Reliability
D.) MTU
E.) Delay | | 1 |
| Identify the OSI layer associated with bits?
A.) Physical
B.) Network
C.) Binary
D.) Data link | | 1 |
| How do you find the parameters that you can use with the SHOW
command?
A.) ? show
B.) show ?
C.) debug show
D.) help
E.) sh? | | 1 |
| What three occurrences will reset the holddown timer after a
triggered
update?
A.) Infinity is finally defined as some max number
B.) HD Timer expires
C.) Another update is received indicating a better metric
D.) The router receives a processing task proportional to
the number of
links in the internetwork
E.) The router detects fault LSP's propagating through the
internetwork
F.) Another update is received indicating net status changed | | 1 |
| What is difference between Store-and-Forward, cut-through,
Fragment-Free Method? | Microsoft | 2 |
| If a router uses dynamic routing, how does it learn the
route to remote networks?
The router uses a DHCP request to obtain remote network
numbers.
The router uses a routing protocol to exchange routing
info. with other routers.
The router uses DNS request packets to obtain remote
network numbers.
The Network Administrator manually configures the remote
networks.
| | 1 |
| What does the 'S' mean when looking at the routing table?
A.) Statically connected
B.) Directly connected
C.) Dynamically attached
D.) Shutdown route | | 2 |
| You are a system administrator and you want to deny access to a
group of computers with addresses 172.30.16.0 to
172.30.31.0. Which
wildcard mask would you use?
A. 0.0.15.255
B. 0.0.255.255
C. 0.0.31.255
D. 0.0.127.255
E. 0.0.255.255 | | 1 |
| Identify the 3 guidelines for routers in the same autonomous
system?
A.) Must be configured for RIP
B.) Interconnected
C.) Assigned the same autonomous system number
D.) Configured for the same routing protocol
E.) Must be same model of router | | 1 |
| Which OSI layer performs code conversion, code formatting and
encryption?
A.) Physical
B.) Data-Link
C.) Application
D.) Transport
E.) Presentation
F.) Network | | 1 |
| Why would you use static routing instead of dynamic routing?
A.) When you want automatic updates of the routing tables
B.) All the time
C.) When you have very few routes and want to conserve bandwidth
D.) When you have a gateway of last resort | | 1 |
| Which of the following is not a characteristic of link-state
routing protocols?
❍ A. VLSM support
❍ B. Route summarization at any bit level
❍ C. Full routing updates at regular intervals
❍ D. Discontiguous network support | | 1 |
| Identify the command to determine if an IP access-list is
grouped
on interface e0?
A.) Router(config)# show ip interface e0
B.) Router> show ip interface e0
C.) Router# show interface e0
D.) Router# show ip interface e0 | | 1 |
| Identify the command to display the Frame Relay map table?
A.) Router# display frame-relay map
B.) Router# show frame-relay map
C.) Router(setup)# show frame-relay map
D.) Router# show map frame-relay | | 1 |
| What are four ways that Fast Ethernet compares to 10BaseT
Ethernet? (Choose four)
A. Fast Ethernet uses the same Maximum Transmission Unit (MTU)
B. Fast Ethernet is based on an extension to the IEEE 802.3
specification
C. Fast Ethernet uses the same Media Access Control (MAC)
mechanisms
D. Fast Ethernet preserves the frame format that is used by
10BaseT Ethernet
E. Fast Ethernet errors a speed increase one hundred times
that of the 10BaseT Ethernet | | 1 |
| Given the global configuration commands:
'banner motd #'
'Hello #'
When would the message be displayed?
A.) The message of the day banner shows up before login.
B.) The message of the day banner shows up during logoff.
C.) These commands are not the right syntax for MOTD.
D.) Message of the day banners are displayed upon entering
global config
mode.
E.) Message of the day banners are not possible.
F.) The message of the day would be, 'Hello #' | | 1 |
| Identify 3 ways in which a router can be configured?
A.) TFTP
B.) Nvram
C.) Ping
D.) Console
E.) Trace | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
