When editing a line in the CLI mode, what does 'CTRL-A' do? A.

Advertise your Business Here

Refer this Site

Login | Sign Up


	Ask Questions on ANYTHING, that arise in your Daily Life at FORUM9.COM

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

When editing a line in the CLI mode, what does 'CTRL-A' do?

A.) Moves you to the previous command.

B.) Moves you to the next word.

C.) Moves you to the end of the line.

D.) Moves you to the next command.

E.) Moves you to the beginning of the line.

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: When editing a line in the CLI mode, what does 'CTRL-A' do? A.) Moves you to the previous command. B.) Moves you to the next word. C.) Moves you to the end of the line. D.) Moves you to the next command. E.) Moves you to the beginning of the line.

Answer
# 1

Answer: E

Is This Answer Correct ?

0 Yes

0 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


What type of frame does CDP use to gather information about it's neighbors? A.) TCP/IP B.) Novell-ether C.) Subnetwork Access Protocol (SNAP) D.) Ethernet_II		1
Where is the backup configuration file stored? A.) RAM B.) ROM C.) Console D.) NVRAM		1
Identify the 3 major functions at layer 3 of the OSI model? A.) Forwarding process B.) Logical addressing C.) End-to-end connnections D.) Path selection E.) MAC address examination F.) Network monitoring		2
Which type of switching is considered to be 'wire speed?' A.) Cut-Through B.) Multiplexed C.) Inverted D.) Layer 4 E.) Store and Forward F.) Layer 3		1
Identify the OSI layer associated with bits? A.) Physical B.) Network C.) Binary D.) Data link		2
Switching methods include cut-through, store and forward, and a modified version of the first two methods. Which statement about switching methods is true? A. The store and forward method has low latency B. The cut through method of switching has high latency C. The modified version holds the packet in memory until 50 percent of the packet reaches the switch D. The modified version holds the packet in memory until the data spoon of the packet reaches the switch		3
Why Clock rate command is not configured on ethernet interface of a router?		4
8. When is Frame Tagging used? A. When you install repeaters in your network B. When you install bridges in your network C. When you install routers in your network D. When you use Switches configured with multiple VLANS		4
MIDI and MPEG are examples of what layer of the OSI seven layer model? A.) Session B.) Network C.) Datalink D.) Transport E.) Application F.) Presentation		4
Identify the 2 methods to modify the routers boot sequence? A.) Setup program B.) Boot system commands C.) RXBoot D.) Config-register		1
By default, Cisco routers forward GNS SAPs to remote networks. A. False B. True		1
1 what is the number of telnet session in the cisco router a 1 b 2 c 3 d 4 e 5		3
What is required to support full-duplex Ethernet? A.) Multiple paths between multiple stations on a link B.) Automatic sensing operation by all connected stations C.) Loopback and collision detection disabled D.) Full-duplex NIC cards		1
What key do you use to view the last command? A.) Ctrl+X B.) Ctrl+Z C.) Ctrl+E D.) Ctrl+P		2
When using RIP, routing updates are broadcast every ____ seconds. A. 30 B. 10 C. 60 D. 90		1
Which of the following is True regarding passwords on a Cisco router? A. All passwords can be encrypted B. All passwords can be entered using the set-up dialogue C. A password can be set before a user can enter the privileged mode D. A password can be set for individual lines E. TACACS or Radius password authentication can be used.		1
WHAT IS SERIAL TRANSMISSIONS,PARALLELL TRANSMISSION	ASD-Lab	2
Identify the command to display the status of the Frame Relay virtual circuit? A.) Router# show frame-relay virtual-circuit B.) Router(config)# show frame-relay pvc C.) Router# show frame-relay pvc D.) Router# show virtual		1
Cisco routers use wildcard masking to identify how to check or ignore corresponding IP address bits. What does setting a wildcard mask bit to 0 cause the router to do? A. It tells the router to check the corresponding bit value. B. It tells the router to ignore the corresponding bit value. C. It tells the router to check its alternate routing list. D. It tells the router to use its primary routing list.		1
When a Distance Vector routing protocol detects that a connected network has gone down, it sends out a special routing update packet, telling all directly connected routers that the distance to the dead network is infinity. This is an example of which routing technology? A.) ICMP. B.) Only Link State routing protocols have this intelligence. C.) Triggered updates. D.) Garrison-4. E.) Split Horizon. F.) Poison Reverse.		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com