| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Can anyone explain in details the STP port state????? | | 2 |
| Identify the command to display the configured IP routing
protocols?
A.) show protocols
B.) show protocols all
C.) show routing-protocols
D.) show ip protocols | | 1 |
| 255.255.255.128/what is the n/w id ,broadcast id and the
number of valid host(according to disco rules) | Reliance | 2 |
| Your network uses a Class C address of 210.10.10.0. You
must now split up the network into separate shores to handle
multiple buildings separated by routers. Which two steps
must you take to determine the proper shored mask for your
networks? (Choose two)
A. determine the number of seperate networks required
B. determine how many devices will require DHCP addressing
C. determine the maximum number of hosts that will be on
each shored
D. determine the miniumum number of hosts that will be on
each shored
E. determine which router will be the IP default gateway for
each shored | | 1 |
| Identify the command to configure the router to boot from an
alternate IOS located in flash?
A.) boot system flash IOS.exe
B.) boot system tftp IOS.exe 172.16.5.1
C.) boot system alternate IOS.exe
D.) boot system rom IOS.exe | | 1 |
| What is the command to manually enter a static route?
A.) IP route network
B.) IP route
C.) IP route < destination network>
D.) IP route | | 4 |
| A banana plantation is located next to a desert. The
plantation owner has 3000 bananas that he wants to transport
to the market by camel, across a 1000 kilometre stretch of
desert. The owner has only one camel, which carries a
maximum of 1000 bananas at any moment in time, and eats one
banana every kilometre it travels. What is the largest
number of bananas that can be delivered at the market? | | 4 |
| Which OSI layer performs code conversion, code formatting and
encryption?
A.) Physical
B.) Data-Link
C.) Application
D.) Transport
E.) Presentation
F.) Network | | 1 |
| What is the IP extended access list range?
A.) 1000-1099
B.) 100-199
C.) 1-99
D.) 101-200 | | 2 |
| Identify the hardware component that stores the bootstrap
program?
A.) ROM
B.) NVRAM
C.) Booter load
D.) RAM
E.) Flash | | 2 |
| Identify the command that will display the RIP routes
entering and
leaving the router?
A.) Router(config)# debug ip rip
B.) Route# debug ip rip
C.) Router>debug ip rip
D.) Router# debug rip routes | | 1 |
| Identify the purpose of the Trace command?
A.) Explorer packet transmitting routing information
B.) Test connectivity
C.) Determine the path a packet is taking through the network
D.) Transmits user data when buffers are full | | 2 |
| Which ISDN specification deals with call Setup and Teardown?
A.) Q-Series
B.) J-Series
C.) I- Series
D.) C- Series
E.) F-Series | | 1 |
| here is your question sahin
Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight
is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1,
K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP.
I knew about it from ICND 2 cisco press book.
Three more questions -
a) If we change the K value (I mean metric weight)on a
router what will happen???
b) When redistribution is necessary in EIGRP. Is there any
condition for that???
c) What is reference bandwidth for metric calculation in
EIGRP. As we know, in OSPF, on a CISCO router reference
bandwidth is 10Mbps. | | 3 |
| After the command -- router igrp 200 -- what command would
enable
IGRP on the router for interface E0, with an address of
157.89.4.4 and a
mask of 255.255.255.0 ?
A.) network 157.89.4.0 255.255.255.1
B.) network 157.89.0.0
C.) router igrp *
D.) router igrp 157.89.0.1
E.) router igrp int e1
F.) router igrp 157.89.4.1 | | 2 |
| 'Show cdp neighbors detail' show the following 3 pieces of
information?
A.) Hardware platform
B.) Software version
C.) Same as 'show version' command
D.) Up to 1 address for each protocol
E.) Non-direct connected routers | | 2 |
| Select the most correct statement regarding client port
address assignment.
The client port always matches the destination port.
To access a web page the client uses the source port of
80 and the destination port is dynamically selected.
When a client requests a web page the destination port
is 80 by default and the source port for the client is
dynamically selected.
The client source port is 1024 to get web pages and 1055
when retrieving ftp files.
| | 2 |
| Which of the following provide correct information about a
protocol at the
transport layer of the OSI model?
A.) UDP - Provides Connectionless datagrams service
B.) TCP - Provides Connection Oriented Services
C.) SMTP - Provides Mail Exchange
D.) IP - Route determination
E.) TCP - Provides Flow Control and Error Checking
F.) FTP - Transfers of Files | | 1 |
| What is the function of the Transport layer and which protocols
reside
there?
A.) MAC addressing - IP
B.) Interhost communication - SQL, NFS
C.) Best effort Packet delivery - TCP, UDP
D.) End-to-end connections - TCP, UDP | | 1 |
| What are four ways that Fast Ethernet compares to 10BaseT
Ethernet? (Choose four)
A. Fast Ethernet uses the same Maximum Transmission Unit (MTU)
B. Fast Ethernet is based on an extension to the IEEE 802.3
specification
C. Fast Ethernet uses the same Media Access Control (MAC)
mechanisms
D. Fast Ethernet preserves the frame format that is used by
10BaseT Ethernet
E. Fast Ethernet errors a speed increase one hundred times
that of the 10BaseT Ethernet | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
