| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which information must a router know in order to perform
proper and pungent routing?
A. destination application of an incoming packet
B. number of other packets in a single flow of data
C. destination network address of an incoming packet
D. number of routers that also know a path to the destination | | 1 |
| here is your question sahin
Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight
is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1,
K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP.
I knew about it from ICND 2 cisco press book.
Three more questions -
a) If we change the K value (I mean metric weight)on a
router what will happen???
b) When redistribution is necessary in EIGRP. Is there any
condition for that???
c) What is reference bandwidth for metric calculation in
EIGRP. As we know, in OSPF, on a CISCO router reference
bandwidth is 10Mbps. | | 3 |
| Which router component stores routing tables APP cache and
packet buffers?
A. ROM
B. RAM
C. AVRAM
D. Flash memory | | 2 |
| What is VLSM? how to Calculate VLSM? where it is use and
why? | | 4 |
| What is the result of using a hierarchical addressing framework?
A. increased availability of addresses
B. decreased distance between routers
C. increased router memory requirements
D. no need to maintain routing information | | 2 |
| The Datalink Layer is broken down into 2 layers, LLC and
MAC. The
LLC establishes media independence and what else?
A.) Provides Windowing.
B.) Provides flow control.
C.) Provides SAP's (Service Access Points).
D.) The Datalink layer does not have sublayers.
E.) Provides SAP's (Service Advertising Protocol).
F.) RIP Updates. | | 1 |
| When you cords an IP address on a place router which command
stale the IP processing on the interface?
A. ip enable
B. network ip-address
C. ip address ip-address subnet mask
D. the exit command from the enabled configuration
E. copy running-configuration to startup-configuration | | 3 |
| Which command displays access list 111?
A. show access-list 111
B. show ip access-list 111
C. display ip access-list 111
D. display access-list 111 details | Satyam | 6 |
| Which IP Address Class can have 16 million subnets but
support 254 hosts?
A. Class C
B. Class A
C. Class B
D. Class D | | 3 |
| What is ISR or NonISR router? Difference between ISR or
NonISR router? | HCL | 3 |
| Identify the 2 commands that will display the status and
information about interface E0 only?
A.) show interface ethernet E0
B.) show interface E0
C.) show E0
D.) show int E0
E.) show interface | | 1 |
| Which of the following is an example of the Physical Layer?
A.) TCP
B.) ARP
C.) IP
D.) FDDI
E.) LLC
F.) Fast Ethernet | | 2 |
| What is Spanning Tree Protocol and how it work? I know it
is - STP is Spanning tree Protocol. It Stops the looping in
the network? How STP work? How it stop Looping in network? | | 2 |
| Identify the prompt displayed if in privileged exec mode?
A.) Router(config)#
B.) Router#
C.) Router>
D.) Router(priv)# | | 1 |
| Station A is transmitting data to station B, and expects an
acknowledgment
after every 400 bytes. After transmitting data for a while,
the two
stations determine the line is reliable and change to
expecting and
acknowledgement every 600 bytes.
This is an example of (pick the best answer only):
A.) BECN
B.) Sliding Windows
C.) Poison Reverse
D.) Countdown timers
E.) Split Horizon
F.) Count to infinity | | 1 |
| Which OSI layer provides best effort end to end packet delivery?
A.) Data-Link
B.) Presentation
C.) Network
D.) Transport
E.) Physical
F.) Application | | 1 |
| Which command loads a new version of the Cisco IOS into a
router?
A. copy flash ftp
B. copy ftp flash
C. copy flash ftp
D. copy tftp flash | | 1 |
| The following is partial output from a routing table,
identify the
2 numbers in the square brackets; '192.168.10.0 [100/1300]
via 10.1.0.1,
00:00:23, Ethernet1'
A.) 100 = metric, 1300 = administrative distance
B.) 100 = administrative distance, 1300 = hop count
C.) 100 = administrative distance, 1300 = metric
D.) 100 = hop count, 1300 = metric | | 1 |
| You just entered the following command_Router(config#) line
console 0 Which operation is most likely to follow?
A. Confound terminal type
B. enter protocol parameters for a serial line
C. create a password on the console terminal line
D. establish a terminal type 4 connection to a remote host
E. change from configuration mode to console privileged mode | Wipro | 10 |
| Your Ethernet interface currently has the IP address of
1.1.1.1/24. You would like it to have a second IP address of
2.2.2.2/24.
Which command will do that?
A.) ip address 1.1.1.1 2.2.2.2 255.255.255.0
B.) ip address 2.2.2.2 255.255.255.0 secondary
C.) ip address 2.2.2.2 255.255.255.0
D.) This cannot be done, you can only have 1 IP address per
physical
interface.
E.) ip address 2.2.2.2 /24 | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
