| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What does the term Base refer to in 100BaseT
A. cabling type
B. singnal type
C. 100 mode type
D. spectrum used
E. speed category | | 2 |
| Identify the correct pair of Novell Ethernet encapsulation
and Cisco
terminology?
A.) Ethernet II, Snap
B.) Ethernet 802.3, Novell-Ether
C.) Ethernet SNAP, Arpa
D.) Ethernet 802.2, Snap | | 1 |
| The following selections show the command prompt and the
configuration of the IP network mask. Which two are
correct?
A. Router#term IP netmask-format { bitcount | decimal |
hexadecimal }
B. Router(config-if)#IP netmask-format { bitcount | decimal
| hexadecimal }
C. Router(config-if)#netmask-format { bitcount | decimal |
hexadecimal }
D. Router#ip netmask-format { bitcount | decimal | hexadecimal } | | 1 |
| Which OSI layer defines end to end communication,
segmentation and
re-assembly?
A.) Network
B.) Transport
C.) Physical
D.) Application
E.) Data-Link
F.) Presentation | | 1 |
| Identify the 3 methods routers learn paths to destinations?
A.) Dynamic routing
B.) None of the above, configured by default
C.) Default routes
D.) Administrative distance
E.) Static routes | | 1 |
| Identify the command to configure the configuration-register?
A.) Router# config-register 0x2102
B.) Router(config)# config-register 0x2102
C.) Router(config-reg)# 0x2102
D.) Router> config-register 0x2102 | | 1 |
| What is the maximum hop count for IP RIP?
A.) Infinity
B.) 16
C.) 15
D.) 1 | Cisco | 2 |
| Identify the command that will display the RIP routes
entering and
leaving the router?
A.) Router(config)# debug ip rip
B.) Route# debug ip rip
C.) Router>debug ip rip
D.) Router# debug rip routes | | 1 |
| From Enable mode, a user types the letter 'C' and presses enter.
There is more than 1 command that starts with 'C'. What
message would
the router return?
A.) Nothing would be returned, the command is simply ignored.
B.) unknown command
C.) ambiguous command.
D.) Copy to?
E.) Configured console from console. | | 1 |
| Why Clock rate command is not configured on ethernet
interface of a router? | | 4 |
| Identify the default IPX serial encapsulation?
A.) Novell-Ether
B.) SDLC
C.) SNAP
D.) HDLC | | 1 |
| What does -1 mean in an extended IPX access-list?
A.) Any IP address
B.) Deny all
C.) Deny host
D.) Any host or any network | | 1 |
| Identify the command to configure DLCI 100 on an interface e0?
A.) Router(config)# frame-relay local-dlci 100
B.) Router(config)# frame-relay local-dlci 100 int e0
C.) Router(config-if)# frame-relay local-dlci 100
D.) Router(config-if)# frame-relay local-dlci 100 int e0 | | 1 |
| Identify the command that configures the bandwidth to 56K?
A.) Router(config-if)# bandwidth 56000
B.) Router(config-if)# bandwidth 56k
C.) Router(config)# bandwidth 56
D.) Router(config-if)# bandwidth 56 | | 1 |
| What is public and private ip address., explain? and also
explain the ip address range of both public and private?
and where we use that public and private ip address? | | 10 |
| Identify the command to display the status of the Frame Relay
virtual circuit?
A.) Router# show frame-relay virtual-circuit
B.) Router(config)# show frame-relay pvc
C.) Router# show frame-relay pvc
D.) Router# show virtual | | 1 |
| Which is true regarding store-and-forward switching method?
A.) Latency varies depending on frame-length
B.) Latency is constant
C.) It is default for all Cisco switches
D.) It only reads the destination hardware address before
forwarding the
frame | | 1 |
| Which three functions are supported by connection oriented
servkps? (Choose three)
A. connection parameters are synchronized
B. any loss or duplication of packets can be corrected
C. the data packet is independently routed and the service
does not guarantee the packet will be processed in order
D. a data communication path is established between a
requesting entity and the peer device on the remote end system | | 1 |
| Identify the keystroke used to terminate the setup mode?
A.) Ctrl-K
B.) Crtl-C
C.) Ctrl-Z
D.) Crtl-End | | 1 |
| What does the trace response !H mean?
* A: Network unreachable
* B: Not forwarded due to ACL restriction
* C: Protocol unreachable
* D: Port could not be reached
| | 2 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
