| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| If you are running Token Ring with Novell IPX routing, which
encapsulation should you use?
A.) SAP
B.) SNAP
C.) 802.5
D.) 802.2 | | 1 |
| What is the IEEE specification for Spanning Tree Protocol?
A.) 802.9
B.) 803.ud
C.) 803
D.) 802.1d | | 1 |
| In version 11.2 of the IOS, a Cisco router configured for
frame-relay can automatically detect the LMI type. What is
this known as?
A.) Psychic
B.) ESP
C.) Inverse ARP
D.) Hello
E.) Reverse ARP
F.) Autosense | | 1 |
| What is the default bandwidth of a serial connection?
A.) 1200 baud
B.) 1.544 Mbps (T1)
C.) 10 Mbps
D.) 96Kpbs | | 3 |
| can we measure how much a host exact bandwidth using by a
network cable which is communicating over the network?
options: 1- via Router 2- Switch, 3- other device... if
yes.. then how ( with every option) | | 3 |
| what is vlan and how will you configure vlan on 3650
switch and how many valn can you create on that switch | Volvo | 3 |
| How do i decide if an extended access-list is in or out?
| | 1 |
| As a system administrator, you want to debug igrp but are
worried that the "debug IP igrp transaction" command will
flood the console. What is the command that you should
use?
A. debug IP igrp event
B. debug IP igrp-events
C. debug IP igrp summary
D. debug IP igrp events | | 1 |
| what is the difference between a passive and active hub??
which is better ?? | | 5 |
| What's the default CDP holdtime in seconds for Cisco routers?
A.) 30 seconds
B.) 180 seconds
C.) 90 seconds
D.) 60 seconds | | 2 |
| what is the high order bit in class a
1
11
110
10
mine answer 1 | | 2 |
| If you are running Token Ring with Novell IPX routing, which
encapsulation
should you use?
A.) SAP
B.) SNAP
C.) 802.5
D.) 802.2 | | 1 |
| IPX routing updates occur how often?
A.) Every 30 seconds
B.) Every 60 seconds
C.) Only as needed
D.) When the remote router asks for an update | | 1 |
| How do you set the encapsulation type to PPP for an interface?
A.) encap ppp
B.) ppp encapsulation
C.) encapsulation ppp
D.) encapsulation ppp enable
E.) ppp enable encapsulation | | 2 |
| Which of the follwing are true of standard half-duplex
Ethernet circuitry?
A. It is alternate one-way communication
B. The receive (RX) is wired directly to the transmit (TX)
of the remote station
C. The transmit (TX) is wired directly to the receive (RX)
of the remote station
D. Collisions are not possible
E. Both stations can transmit simultaneously | | 1 |
| A ISDN PRI circuit can be described as which of the following?
A.) 24 B channels and 1-64Kbps D channel
B.) 23 B channels and 1-64Kbps D channel
C.) 2-D channels and 1-C channel
D.) 2-64Kbps B channels and 1-16Kbps D channel | | 1 |
| I want to configure a serial interface on a 7500 with a VIP
card.
What global config command would give me access to a serial
interface on
a 7500?
A.) int 1/0/0
B.) int s 1/0/0
C.) int s 1/1
D.) int s0.1
E.) int s1 | | 1 |
| Which statement is true regarding full duplex?
A.) Allows for transmission and receiving of data simultaneously
B.) Only works in a multipoint configuration
C.) Does not affect the bandwidth
D.) Allows for transmission and receiving of data but not a
the same time | | 2 |
| Which layer is responsible for coordinating communication
between
systems?
A.) Application
B.) Network
C.) Session
D.) Transport
E.) Physical
F.) Data Link | | 1 |
| Identify the 3 major functions at layer 3 of the OSI model?
A.) Forwarding process
B.) Logical addressing
C.) End-to-end connections
D.) Path selection
E.) MAC address examination
F.) Network monitoring | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
