ALLInterview.com :: Home Page KalAajKal.com
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
tip   To Refer this Site to Your Friends   Click Here
Google
 
Categories  >>  Certifications  >>  Cisco Certifications  >>  CCNA
 
 


 

 
 CCNA interview questions  CCNA Interview Questions
 CCDA interview questions  CCDA Interview Questions
Question
Which command do you use to set the Privileged mode password to

'clearwater'?

A.) set password=clearwater

B.) enable privilege password clearwater

C.) enable password clearwater

D.) enable login clearwater

E.) enable secret password clearwater

F.) ebable clearwater
 Question Submitted By :: Guest
I also faced this Question!!     Rank Answer Posted By  
 
  Re: Which command do you use to set the Privileged mode password to 'clearwater'? A.) set password=clearwater B.) enable privilege password clearwater C.) enable password clearwater D.) enable login clearwater E.) enable secret password clearwater F.) ebable clearwater
Answer
# 1
Answer: C
 
Is This Answer Correct ?    1 Yes 2 No
Guest
 

 
 
 
Other CCNA Interview Questions
 
  Question Asked @ Answers
 
what is the difference between 1 router and switch 2 router and hub 3 hub and switch 4 bridge and switch Hathway1
what are the 3ree way for implementing vlan on cisco switches what is the layer hierarchy of the cisco what is the best place of implementing standard access list what is q stand for isdn these are the challanging question for me i am waiting for jitendera sinha answer(it is challenge for u i have seen lots of answer given by u )it is a challenge in the frendshipmode plz donot take other wise  2
Identify 3 characteristics of ISDN? A.) Transports voice and data B.) Transports voice only C.) Support both BRI and PRI D.) Runs over existing phone lines E.) Same as X.25  1
The Cisco Discovery Protocol (CDP) periodically sends out a multicast packet (at layer 2). Which command will alter the default interval of 60 seconds? A.) cdp hold 111 B.) cdp wait 111 C.) cdp interval 111 D.) cdp 111 E.) cdp timer 111  1
what is ip address and what is the difference between the ip address and mac address why we are not using mac address instead of ip address IBM3
Identify 2 characteristics of PPP? A.) Uses LLC to establish the link B.) Default serial encapsulation C.) Support multiple layer 3 protocols D.) Offers two types of authentication; PAP and CHAP  1
Novell NetWare has an Ethernet frame type called Ethernet_II. What is the matching Cisco command line keyword for this encapsulation method? A.) dix B.) sap C.) arpa D.) gns E.) snap F.) novell-ether  1
thnx jitender...its me shridh...m working for SG ltd..the situation iz like ths -at a specific time in our company the internet connectivity goes off...v hav two networks in our company...but out of it only one link goes down for 5-10 sec...a fastethernet port becomes down for few sec and automatically becomes Up... Is this occures becoz of Power?? If yes thn y the 2nd network is not affected?? plz tel me jitender how to resolve ths problem? as u sd loop in switch is the primary cause of ths....i wanna know how to resolve it...thnx for ur replys jitender sinha.  2
Which command allows a user to see previous commands? A.) show command B.) CTRL-P C.) show history D.) CTRL-U E.) Up Arrow F.) SHIFT-CTRL-6  1
What does the "IPX maximum-paths 2" command accomplish? A. It enables load sharing on 2 paths if the paths are equal metric paths. B. It sets up routing to go to network 2. C. It is the default for Cisco IPX load sharing. D. It enables load sharing on 2 paths if the paths are unequal metric paths.  2
Which of the following is an example of the Network Layer? A.) TCP B.) IP C.) SQL D.) Token Ring E.) LLC  1
Identify the command to configure the IP address 172.16.100.5 255.255.255.0? A.) Router(config-if)# ip address 172.16.100.5 255.255.255.0 B.) Router(config)# ip address 172.16.100.5 C.) Router# ip address 172.16.100.5 255.255.255.0 D.) Router(config)# ip address 172.16.100.5 255.255.255.0  1
What is the default LMI type for Cisco Routers that are using Frame-Relay? A.) Gandalf5 B.) Q933A C.) Cisco D.) IETF E.) ARPA F.) SAP  2
what is the difference between a passive and active hub?? which is better ??  5
WAN stands for which of the following? A.) Wide Arena Network B.) World Area Network C.) Wide Area News D.) Wide Area Network  1
The maximum distance on a 10BaseT network from the hub to a workstation is which of the following? A.) 500 meters B.) 1000 meters C.) 100 meters D.) 1500 meters  2
Which IP Address Class can have 64,000 subnets with 64,000 hosts per subnet? A. Class B B. Class A C. Class C D. Class D  2
Which cable do you use to connect a PC directly to the fast ethernet interface on a router. For example if you wanted to do an IOS upgrade from your laptop?  5
An autonomous system can only exist if all routers in that system meet which criteria? A. interconnected B. run the same routing protocol C. assigned same autonomous system number D. run IGRP only E. run RIP only  1
what is meant by domain ? what is mean by DNS?  14
 
For more CCNA Interview Questions Click Here 
 
 
 
 
 
   
Copyright Policy  |  Terms of Service  |  Help  |  Site Map 1  |  Articles  |  Site Map  |   Site Map  |  Contact Us interview questions urls   External Links 
   
Copyright © 2007  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  Forum9.com   ::  KalAajKal.com