Which command will copy the routers configuration from NVRAM to a Netwo

Advertise your Business Here

Refer this Site

Login | Sign Up


	Ask Questions on ANYTHING, that arise in your Daily Life at FORUM9.COM

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

Which command will copy the routers configuration from NVRAM
to a

Network file server?

A.) copy start tftp

B.) copy start tftp server

C.) copy tftp startup-config

D.) copy running-config tftp

E.) copy startup-config tftp

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: Which command will copy the routers configuration from NVRAM to a Network file server? A.) copy start tftp B.) copy start tftp server C.) copy tftp startup-config D.) copy running-config tftp E.) copy startup-config tftp

Answer
# 1

Answer: A E

Is This Answer Correct ?

2 Yes

1 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


Based upon the 1st octet rule identify the range for a Class A address? A.) 1 - 126 B.) 192 - 223 C.) 128 - 191 D.) 1 - 191		1
Which layer defines the physical topology? A.) Application B.) Transport C.) Network D.) Data Link E.) Physical F.) Session		1
Routers that have Flash memory typically have a ore loaded copy of place IOS software. Which command should you use to make a backup copy of the software image onto a given network server? A. copy flash tftp B. save copy to tftp C. write backup tftp D. write, backup -server-name- E. copy backup to -server-name-		1
Novell NetWare has an Ethernet frame type called Ethernet_SNAP. What is the matching Cisco command line keyword for this encapsulation method? A.) arpa B.) sap C.) snap D.) gns E.) dix F.) novell-ether		1
What layer can optionally support reliability? A.) Transport B.) IP C.) Physical D.) Network E.) Sub-physical layer		1
Identify 2 features of X.25? A.) Supports only IP B.) Utilizes switched and permanent virtual circuits C.) Contains minimal flow control and error recovery D.) Utilizes LAPB as it's data-link protocol		1
Identify the command to reload the router? A.) Router(config)# reload B.) Router# reset C.) Router# reload D.) Router> reload		1
Which of the following is true regarding standard ISDN BRI service? A.) ISDN BRI B channels are typically 64K. B.) ISDN BRI can handle only voice. C.) ISDN BRI can handle only data. D.) ISDN BRI has 2B and 1D channels. E.) ISDN BRI D channels are 16K. F.) ISDN BRI can handle voice and data.		2
Write out a config to permit only the below MAC address to pass traffic through a port on your switch. mac-address 0005.1b00.5b58		4
Which two statements about a bridge are true? (Choose two) A. A bridge floods multicasts B. A bridge floods broadcasts C. A bridge does not flood multicasts D. A bridge does not flood broadcasts		1
Which of the following are examples of ICMP? A.) Traceroute B.) Web Browsing C.) Ping D.) Telnet E.) Destination Unreachable message from a router F.) Inverse Tunnels		1
Which command verifies encapsulation as well as Layer 1 and Layer 2 statistics on a router configured for Frame Relay? A. show ip B. show interface C. show statistics D. show frame-relay		1
What is the syntax to add a banner to the Cisco router? A.) motd banner # B.) banner C.) banner motd # D.) banner #		1
The benefits to segmenting with Bridges are which of the following? A.) Scalability B.) Datagram filtering C.) Manageability D.) Reliability		1
Can anyone explain the Split Horizon rule in RIP & also Split Horizon with Poison reverse. Jitu.... U knw wat i expect.. hehehehehe...		1
Which symbol in the router prompt indicates you are in the privelaged mode? A. > B. ! C. # D. :		3
Most routing protocols recognize that it is never useful to send information about a route back out the direction from which the original packet came. This is an example of which routing technology? A.) Split Horizon B.) LMI C.) Triggered Updates D.) Poison Reverse E.) SYN, ACK F.) DLCI		1
Which layer allows multiple Ethernet devices to uniquely identify one another on the Datalink layer? A.) Transport B.) Session C.) Network D.) Datalink - MAC Sublayer E.) Datalink - LLC Sublayer		3
Which statement about the Committed Information Rate (CIP) is true? A. It is the rate in bits per second at which the Frame Relay switch agrees to transfer data B. It is the clock speed (pod speed) of the connection (local loop) to the Frame Relay cloud C. It is the maximum number of bits that switch can transferduring any Committed Rate Measurement Interval D. It is a signaling standard between the 3PE device and FP switch. It is responsible for managing the connection and maintaining status between the devices.		1
The default routing protocol for IPX is IPX RIP. How do you view the routing updates sent and received by the router? A.) debug ipx routing B.) debug ipx routing activity C.) debug rip D.) show ipx routing E.) sh ipx F.) debug ipx rip		2

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com