| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is the default encapsulation of Netware 3.12?
A.) Ethernet_II
B.) 802.5
C.) 802.2
D.) 802.3 | | 1 |
| Why ESP Transport mode is not compatible with NAT?????
Though New IP Header in Tunnel mode & Original IP Header in
Transport mode are out of Authentication & Encryption. | | 1 |
| If a router uses static routing, how does it learn the
route to remote networks?
The router uses a RIP request to obtain remote network
numbers.
The router uses a routing protocol to exchange remote
network numbers.
The router uses DNS request packets to obtain remote
network numbers.
The Network Administrator manually configures the remote
networks.
| | 1 |
| What is the Difference between Switch and Bridge? | | 3 |
| Given the following output, how can we close Telnet session
2? (Choose two)
CCNA2620#show sessions
Conn Host Address Idle Conn Name
1 131.108.100.152 131.108.100.152 0 131.108.100.152
*2 126.102.57.63 126.102.57.63 0 126.102.57.63
❍ A. Press the Enter key and enter exit.
❍ B. Enter disconnect 2.
❍ C. Press the Enter key and enter disconnect 2.
❍ D. Enter close 2. | | 1 |
| What does the term Base refer to in 100BaseT
A. cabling type
B. singnal type
C. 100 mode type
D. spectrum used
E. speed category | | 2 |
| WAN stands for which of the following?
A.) Wide Arena Network
B.) World Area Network
C.) Wide Area News
D.) Wide Area Network | | 1 |
| Identify 3 characteristics of IP RIP?
A.) Distance vector
B.) Administrative distance is 120
C.) Periodic updates every 60 seconds
D.) Uses a composite metric
E.) Can load balance | | 1 |
| Which feature of PPP (Point to Point Protocol) allows the router
to bind multiple channels together, to form a single logical
channel?
A.) multi-link ppp
B.) multi-channel ppp
C.) can't be done
D.) omni-ppp
E.) plp | | 1 |
| what is the diffrence betwwen telnet and ssh.this question
is asked by nikhil and i am plasing the answer here insteed
of his personal mail.
| | 4 |
| tell me our traditional ip routing is what
A--conectless
b----conection orented
c-----pacekt switching
d------ckt switching
slect any two
this is the question which i forgot to incoprate
next-questions
| | 3 |
| Which statement is true regarding full duplex?
A.) Allows for transmission and receiving of data simultaneously
B.) Only works in a multipoint configuration
C.) Does not affect the bandwidth
D.) Allows for transmission and receiving of data but not a
the same time | | 2 |
| Which command will display adjacent routers found by the Cisco
Discovery Protocol?
A.) show all
B.) show cdp entry
C.) show ip neighbors
D.) show cdp neighbor detail
E.) show cdp neighbor
F.) show neighbor | | 1 |
| Identify the command to determine if CDP is enabled?
A.) show enable cdp
B.) show cdp enabled
C.) show cdp run
D.) show cdp | | 2 |
| The command "show IP protocol" displays which information?
A. routing timers
B. network information
C. contents of the IP routing table
D. information about all known network and subnetworks | | 2 |
| What are the 3 ways routers learn paths to destination networks?
A.) Dynamic
B.) Static
C.) Routing tables
D.) Default | | 1 |
| Which layer defines bit synchronization?
A.) Application
B.) Network
C.) Transport
D.) Physical
E.) Session
F.) Session | | 1 |
| What is the function of Layer 2 Switch? | | 1 |
| What is BGP attribute & How many types of attributes are
used by BGP??? | Hathway | 3 |
| Which show underrate serial 1 status statement indicates
that the shutdown command was issued on that interface?
A. Serial 1 is up line protocol is up
B. Serial 1 is up line protocol is down
C. Serial 1 is down line protocol is down
D. Serial 1 is administratively down the line protocol is down | Pioneer-Labs | 2 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
