| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify 2 HDLC characteristics?
A.) Default serial encapsulation
B.) Open standard
C.) Supports Stacker compression
D.) Supports point-to-point and multipoint | | 1 |
| If i connect two routers through ethernet cable and serial
cable then which has high speed and which is better among
two? | Compaq | 9 |
| Identify the command to configure the router to boot from an IOS
located on a TFTP server?
A.) boot system tftp IOS.exe 172.16.5.1
B.) boot system tftp 172.16.5.1 IOS.exe
C.) boot system flash tftp 172.16.5.1
D.) boot system IOS.exe 172.16.5.1 | HCL | 2 |
| What is the IP extended access list range?
A.) 1000-1099
B.) 100-199
C.) 1-99
D.) 101-200 | | 2 |
| What type of frame does CDP use to gather information about it's
neighbors?
A.) TCP/IP
B.) Novell-ether
C.) Subnetwork Access Protocol (SNAP)
D.) Ethernet_II | | 1 |
| Which global configuration command will tell the router to load
the IOS file 'IOS_filename' from the Network File server at
1.2.3.4
during the next boot?
A.) boot system flash IOS_filename 1.2.3.4
B.) boot system tftp IOS_filename 1.2.3.4
C.) config-register 0x0 1.2.3.4
D.) boot system rom 1.2.3.4
E.) This can not be done, only the first file in flash can
be used. | | 1 |
| How do you disable CDP on the entire Router?
A.) Router#no cdp run
B.) Rotuer(config-if)# no cdp enable
C.) Router(config)# no cdp enable
D.) Router(config)# no cdp run | | 1 |
| The Physical layer works with which of the following:
A.) Segments
B.) Datagrams
C.) Packets
D.) Bits
E.) Frames | | 1 |
| Which OSI Reference Layer controls application to application
communication?
A.) Datalink
B.) Network
C.) Transport
D.) Session
E.) Physical | | 1 |
| Which of the following are solutions to the problems encountered
with Distance-Vector routing?
A.) Defining a Maximum
B.) Poison Reverse
C.) Triggered Updates
D.) Shortest path first algorithm.
E.) Split Horizon | | 1 |
| Where is the backup configuration file stored?
A.) RAM
B.) ROM
C.) Console
D.) NVRAM | | 1 |
| The Datalink Layer is broken down into 2 layers, LLC and
MAC. The
LLC establishes media independence and what else?
A.) Provides Windowing.
B.) Provides flow control.
C.) Provides SAP's (Service Access Points).
D.) The Datalink layer does not have sublayers.
E.) Provides SAP's (Service Advertising Protocol).
F.) RIP Updates. | | 1 |
| Identify the 3 major functions at layer 3 of the OSI model?
A.) Forwarding process
B.) Logical addressing
C.) End-to-end connections
D.) Path selection
E.) MAC address examination
F.) Network monitoring | | 1 |
| Identify the command to view the configuration-register value?
A.) show register
B.) display config-register
C.) show config
D.) show version | | 1 |
| Which NetWare protocol provides link-state routing?
A. NLSP
B. RIP
C. SAP
D. NCP | | 1 |
| Identify 2 features of PPP CHAP authentication?
A.) Username and password is sent in clear text
B.) Authentication messages are sent periodically during the
connection
C.) Less secure then PAP
D.) Local router 'challenges' the remote router | | 1 |
| What is the purpose of the DLCI?
A.) Identifies the remote routers
B.) Contained with a 802.2 frame for routing purposes
C.) Used with PPP during authentication
D.) Identifies the PVC in a Frame Relay network | | 1 |
| Identify the 3 guidelines for routers in the same autonomous
system?
A.) Must be configured for IGRP or RIP
B.) Interconnected
C.) Assigned the same autonomous system number
D.) Configured for the same routing protocol
E.) Must be same model of router | | 1 |
| WAN stands for which of the following?
A.) Wide Arena Network
B.) World Area Network
C.) Wide Area News
D.) Wide Area Network | | 1 |
| Identify the components in the following command 'interface
serial0/1/1'
A.) Serial interface, port number 0, slot 1, port adapter 1
B.) Serial interface, slot 1, port number 1, port adapter 0
C.) Serial interface, slot 0, port adapter 1, port number 1 | | 1 |
| |
| For more CCNA Interview Questions Click Here |