| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which protocol will send a message to routers if a network
outage or
congestion occurs?
A.) ARP
B.) TCP
C.) IP
D.) ICMP | | 1 |
| Identify the default values that make up IGRP's composite
metric?
A.) Bandwidth
B.) Load
C.) Reliability
D.) MTU
E.) Delay | | 1 |
| Your network uses a Class C address of 210.10.10.0. You
must now split up the network into separate shores to handle
multiple buildings separated by routers. Which two steps
must you take to determine the proper shored mask for your
networks? (Choose two)
A. determine the number of seperate networks required
B. determine how many devices will require DHCP addressing
C. determine the maximum number of hosts that will be on
each shored
D. determine the miniumum number of hosts that will be on
each shored
E. determine which router will be the IP default gateway for
each shored | | 1 |
| What does -1 mean in an extended IPX access-list?
A.) Any IP address
B.) Deny all
C.) Deny host
D.) Any host or any network | | 1 |
| Identify 1 characteristic of RARP?
A.) MAC to IP address translation
B.) Connectionless delivery of packets
C.) Can be used to initiate remote O/S load sequence
D.) Generates error and control messages | | 2 |
| UDP works at which layer of the DOD model?
A.) Internet
B.) Host-to-Host
C.) Transport
D.) Data Link | | 1 |
| What is the command to allow you to type Tokyo instead of the IP
address 172.16.30.1 to access a router named Tokyo?
A.) config t, ip host Tokyo 172.16.30.1
B.) config t, ip hostname Tokyo 172.16.30.1
C.) config t, hostname Tokyo 172.16.30.1
D.) config t, ip hostname 172.16.30.1 Tokyo | | 1 |
| What is the function of Layer 2 Device? | | 2 |
| What is the administrative distance for IGRP?
A.) 90
B.) 120
C.) 110
D.) 100 | | 2 |
| what is the difference between a passive and active hub??
which is better ?? | | 2 |
| Identify the command to display the Frame Relay map table?
A.) Router# display frame-relay map
B.) Router# show frame-relay map
C.) Router(setup)# show frame-relay map
D.) Router# show map frame-relay | | 1 |
| Which of the following is an example of the Network Layer?
A.) Token Ring
B.) RARP
C.) LLC
D.) DDP
E.) TCP | | 1 |
| What is the maximum number of subnets that can be assigned
to networks when using the address 172.16.0.0 with a subnet
mask of 255.255.240.0? (Assume older version UNIX
workstations are in use.)
A. 16
B. 32
C. 30
D. 14
E. It is an invalid subnet mask for the Network. | | 1 |
| Which symbol in the router prompt indicates you are in the
privelaged mode?
A. >
B. !
C. #
D. : | | 3 |
| Which of the following is a valid extended IP access-list?
A.) router(config)# access-list 101 permit tcp host
172.16.30.0 any eq
21 log
B.) router# access-list 101 permit tcp host 172.16.30.0 any
eq 21 log
C.) router(config)# acess-list 101 permit any any 172.16.30.0
D.) router(config)# access-list 101 permit ip host
172.16.30.0 any eq 21
log | HCL | 1 |
| Which statement about the Point to Point Protocol (PPP) is true?
A. PPP supports TCP/IP but not Novell IPX
B. PPP is being phased out of existence by the Serial Line
Internet Protocol (SLIP)
C. PPP providces router to router and host to network
connections over both synchronous and asynchronous circuits
D. PPP is an ITU T and ANSI standard that defines the
process for sending data over a packet switched data network
(PSDN) | | 1 |
| What is the command to manually enter a static route?
A.) IP route network
B.) IP route
C.) IP route < destination network>
D.) IP route | | 1 |
| You would like to have a notation that when a user issues
the command
'show interface serial 0', a line is displayed indicating
that, 'This is
the connection to Company A.' What interface command would
accomplish this?
A.) banner motd #This is the connection to Company A.#
B.) interface This is the connection to Company A.
C.) This cannot be done for an individual interface.
D.) description This is the connection to Company A.
E.) banner This is the connection to Company A.
F.) display This is the connection to Company A. | | 1 |
| Which layer is responsible for coordinating communication
between
systems?
A.) Application
B.) Network
C.) Session
D.) Transport
E.) Physical
F.) Data Link | HCL | 1 |
| Which addresses are INCORRECTLY paired with their class?
A. 128 to 191, Class B
B. 192 to 223 Class B
C. 128 to 191, Class C
D. 192 to 223, Class C | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map