| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which OSI layer supports the communication component of an
application?
A.) Data-Link
B.) Physical
C.) Session
D.) Presentation
E.) Application
F.) Transport | | 1 |
| Identify the statement which connects access-list 101 inbound to
interface e0?
A.) Router(config-if)# ip access-group 101 in
B.) Router(config-if)# ip access-group 101
C.) Router(config)# ip access-group 101 e0 in
D.) Router(config)# ip access-group 101 e0 in | | 1 |
| Identify 3 characteristics regarding IP access-lists?
A.) Can be configured as a standard access-list
B.) Can be run from another router running IP
C.) Can be configured as a named access-list
D.) Are the same as IPX access-lists
E.) Can be configured as an extended access-list | | 1 |
| What does a Standard IP Access-list use as test criteria?
A.) IP source address
B.) IP source and destination address, protocol numbers and
port numbers
C.) IPX source and destination address
D.) Source MAC address | | 1 |
| What is the difference between TCP and UDP?
A.) TCP is connection-oriented; UDP uses acknowledgements only
B.) TCP is connection-oriented; UDP is connectionless
C.) Both TCP and UDP are connection-oriented, but only TCP
uses windowing
D.) TCP and UDP both have sequencing, but UDP is connectionless | | 2 |
| Identify the 2 commands that copies the configuration in
NVRAM to
RAM?
A.) copy backup-config running-config
B.) configure nvram
C.) copy startup-config running-config
D.) configure memory | | 2 |
| Put the following steps of encapsulation into the correct order:
1) The data is broken into segments to be organized
2) Frames are converted to 1s and 0s to be put on the wire
3) Packets are converted into frames
4) Information that users enter is converted into data
5) The segments are changed to packets to be routed
A.) 4, 1, 3, 2, 5
B.) 4, 5, 1, 3, 2
C.) 2, 3, 1, 4, 5
D.) 4, 1, 5, 3, 2 | | 1 |
| What does the command show access-lists 101 list?
A. all defended access lists
B. all access lists within the router
C. the contents of standard access list 101
D. the contents of defended access list 101 | | 1 |
| As system administrator, you type "debug ipx sap" and
receive the following lines as part of the IOS response:
type 0x4, "HELLO2", 199.0002.0003.0006 (451), 2 hops
type 0x4, "HELLO1", 199.0002.0003.0008 (451), 2 hops
What does "0x4" signify?
A. That is a Get Nearest Server response.
B. That it is a General query.
C. That it is a General response.
D. That it is a Get Nearest Server request. | | 1 |
| What is the first step in data encapsulation?
A.) User information is converted into data.
B.) Frames are put into bits.
C.) Data is converted into segments.
D.) Segments are converted into datagrams and packets.
E.) Packets are put into logical frame. | | 1 |
| What is the function of DDR on Cisco routers?
A. DDR is dial--on-demand routing. It provides a continuous
LAN only
connection.
B. DDR is dial-on-demand routing. It provides routing for
high volume
traffic.
C. DDR is dial--on-demand routing. It provides a continuous
WAN connection.
D. DDR is dial-on-demand routing. It provides routing for
low volume and
periodic traffic. | | 2 |
| Describe End to End network services: (Choose all that apply)
A.) Best Route selection
B.) Accomplished Segment by Segment, each segment is autonomous
C.) Flow Control & Data Integrity
D.) Best efforts packet delivery | | 1 |
| What is the default LMI type for Cisco Routers that are using
Frame-Relay?
A.) Gandalf5
B.) Q933A
C.) Cisco
D.) IETF
E.) ARPA
F.) SAP | | 1 |
| Which OSI layer provides best effort end to end packet delivery?
A.) Data-Link
B.) Presentation
C.) Network
D.) Transport
E.) Physical
F.) Application | Barnes-and-Noble | 1 |
| Which routing protocols uses connection-oriented routing
updates?
A.) IGRP
B.) UDP
C.) RIP
D.) IP
E.) BGP | | 1 |
| Identify the command to display the Frame Relay map table?
A.) Router# display frame-relay map
B.) Router# show frame-relay map
C.) Router(setup)# show frame-relay map
D.) Router# show map frame-relay | | 1 |
| Which command line statement determines the number of seconds a
dialup connection can wait without any traffic before the
router hangs up?
A.) dialler max-time
B.) dialler timeout
C.) dialer idle-timeout
D.) dialer hang-up
E.) disconnect-timer | | 2 |
| Identify the command to display the IP routing table?
A.) show route
B.) show ip route
C.) show ip table route
D.) show ipx route | | 1 |
| Which two steps are required to confound and apply standard
access lists on an interface? (Choose two)
A. define an access list number and its parameters
B. enable an interface to become part of the access list group
C. define the number of access lists to be supported on an
interface
D. copy the access list definition to each interface that
will support it | | 2 |
| LMI operates between the Frame Switch and what other device?
A.) CPE device
B.) Another Frame Switch
C.) X.25 switch
D.) Novell File Server | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
