| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Your Ethernet interface currently has the IP address of
1.1.1.1/24. You would like it to have a second IP address of
2.2.2.2/24.
Which command will do that?
A.) ip address 1.1.1.1 2.2.2.2 255.255.255.0
B.) ip address 2.2.2.2 255.255.255.0 secondary
C.) ip address 2.2.2.2 255.255.255.0
D.) This cannot be done, you can only have 1 IP address per
physical
interface.
E.) ip address 2.2.2.2 /24 | | 1 |
| How do you disable CDP on the entire Router?
A.) Router#no cdp run
B.) Rotuer(config-if)# no cdp enable
C.) Router(config)# no cdp enable
D.) Router(config)# no cdp run | | 1 |
| At which layer of the OSI Reference Model do bridges operate?
A.) Physcial
B.) Session
C.) Datalink
D.) Transport
E.) Network | | 2 |
| Which of the following are valid WAN terms?
A.) DTE
B.) DCE
C.) Demarc
D.) CPE | | 2 |
| What does a router do with a packet that it does not have a
destination network for?
A.) Sends it to the Serial port
B.) Drops the packet
C.) Sends it back out the same interface it received it in
D.) Forwards the packet to the next hop | | 2 |
| What are the generic parts of a network layer address?
A. an intenetworks number and a URL
B. a vendor code and a serial number
C. a network number and a host number
D. a broadcast number and a unicast number
E. a domain identifier and a device identifier | | 1 |
| Identify the 2 commands that copies the configuration in
NVRAM to
RAM?
A.) copy backup-config running-config
B.) configure nvram
C.) copy startup-config running-config
D.) configure memory | | 2 |
| which portecol is faster
tcp
udp
spx | | 5 |
| Put the following steps of encapsulation into the correct order:
1) The data is broken into segments to be organized
2) Frames are converted to 1s and 0s to be put on the wire
3) Packets are converted into frames
4) Information that users enter is converted into data
5) The segments are changed to packets to be routed
A.) 4, 1, 3, 2, 5
B.) 4, 5, 1, 3, 2
C.) 2, 3, 1, 4, 5
D.) 4, 1, 5, 3, 2 | | 1 |
| You have two Cisco routers setup back-to-back in a lab using
DTE/DCE cables. To which router would you add the clockrate
command?
A.) The serial port on the DCE router
B.) The Ethernet port on the DTE router
C.) The Ethernet port on the DCE router
D.) The serial port on the DTE router | TCS | 3 |
| hi friends i am jitendera kumar sinha.i have a question in
mind that what is the diffrence between router and l3 switch
i serched on google and found that switch L3 is best in lan
and router are best in wan and switch are more faster then
router.beside that any short of technical diffrence if you
body know then plz plz and plz reply.
my 2nd question is that why we canot replace router with L3
switches (donot tell that it is costly then router).i want
any technical cause.
this is 1 am hope in noon when ever i logg again i will find
the answer posted by you.
thanks onse again
plz pzl make reply
thanks
jitendera kumar sinha
jitenerasinha.it@gmail.com
| | 5 |
| A network is vow congested currently all the devices are
connected through a hub. Which would best decrease
congestion on this network?
A. add a second hub
B. replace the hub with a router
C. replace the hub with a switch
D. replace the hub with a repeater | | 1 |
| Identify the 2 types of access-list filters that control SAP
traffic?
A.) Novell-ether
B.) Arpa
C.) Input-sap-filter
D.) Round-robin
E.) Output-sap-filter | | 1 |
| Most routing protocols recognize that it is never useful to send
information about a route back out the direction from which
the original
packet came. This is an example of which routing technology?
A.) Split Horizon
B.) LMI
C.) Triggered Updates
D.) Poison Reverse
E.) SYN, ACK
F.) DLCI | | 1 |
| Identify the named IP access-list number range?
A.) 600 - 699
B.) 1 - 99
C.) 900 - 999
D.) 200 - 299
E.) none of the above | | 2 |
| What is the Difference between Hub and Switch? | | 2 |
| Which show underrate serial 1 status statement indicates
that the shutdown command was issued on that interface?
A. Serial 1 is up line protocol is up
B. Serial 1 is up line protocol is down
C. Serial 1 is down line protocol is down
D. Serial 1 is administratively down the line protocol is down | Pioneer-Labs | 2 |
| If you are running Token Ring with Novell IPX routing, which
encapsulation
should you use?
A.) SAP
B.) SNAP
C.) 802.5
D.) 802.2 | | 1 |
| Which command-line keywords are valid for choosing
Frame-Relay LMI
types?
A.) itu-t
B.) dlci
C.) ansi
D.) rfc 1544
E.) cisco
F.) q933a | | 1 |
| What IP command would you use to test the entire IP stack?
A.) Stack-test
B.) Arp
C.) Telnet
D.) Ping
E.) Trace | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
