| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| As a system administrator, you perform an extended ping at
the privileged EXEC prompt. As part of the display, you see
"Set DF bit in IP header? [yes] :" What would happen if you
answered no at the prompt.
A. This lets the router fragment the packet.
B. It tells the router not to fragment the packet.
C. This lets the router direct the packet to the destination
it finds in its routing table.
D. It tell the router to send the packet to the next hop
router. | | 1 |
| The Network layer works with which of the following:
A.) Globules
B.) Bits
C.) Packets
D.) Segments
E.) Frames | | 2 |
| Identify the definition of demarcation?
A.) Date in which the WAN service contract expires
B.) Cabling which extends from the WAN service provider to
the customer
C.) Division of responsibility, where the CPE ends and the
local loop
begins
D.) Equipment which is located at the customer premises | | 1 |
| In regards to the ISDN BRI standard, which channel is used for
control?
A.) B
B.) D
C.) E
D.) I
E.) Q | | 2 |
| Which commands should you use to enable IGRP routing?
A. router igrp 100
Network 192.168.1.0
Network 10.0.0.0
B. router igrp 100
Network 192.168.2.0
Network 10.0.0.0
C. router igrp 100
Network 192.168.1.0 192 168.1.1
Network 10.2.0.0 10.2.1.1
D. router igrp 100
Network 192.168.1.0 255.255.255.0
Network 10.2.0.0 255.255.255.0 | | 2 |
| The Cisco IOS is stored in:
A.) ROM
B.) CD
C.) Flash
D.) NVRAM | | 3 |
| What is the Broadcast IP Address? | | 11 |
| Which two statements are true? (Choose two)
A. Ethernet 802.3 utilizes a half duplex method for data
transfer
B. In a 100 MBS point to point connection a full duplex
connection can provide 400 Mbs of data transfer
C. Ethernet switches can use the full duplex mode to connect
multiple nodes on a single pod of a switch
D. Full duplex Ethernet takes advantage of UTP using one
pair for transmission and the other pair for reception | | 1 |
| Inverse ARP serves what purpose?
A.) Method for a local router to introduce itself to the
remote end of the
connection
B.) Broadcast a routing table update
C.) Identify MAC addresses if the IP address is known
D.) Sent every 10 seconds used to verify the Frame Switch is
still active | | 1 |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| Which OSI layer establishes, maintains and terminates sessions
between hosts?
A.) Application
B.) Physical
C.) Data-Link
D.) Presentation
E.) Network
F.) Session | | 1 |
| what is diffrence between circit switching and packet
switching | Volvo | 1 |
| When discussing static routes, what is the gateway parameter
used
for?
A.) Determining the dynamic route
B.) Defining the subnet
C.) Defining the Administrative Distance
D.) Determining the next hop | | 1 |
| What does the ping response & mean?
* A: unreachable
* B: congestion
* C: user interrupt
* D: unknown packet type
* E: lifetime exceeded
| | 2 |
| Which command will display the current time on a Cisco router?
A.) show date
B.) show clock
C.) show running-configuration
D.) show time
E.) show controllers | | 2 |
| Which of the following is true?
A. The default is to send debug output to the console screen.
B. To view debug output from a telnet session, the "terminal
monitor" command must be used
C. If the "logging buffered" command is used, the debug
output would be sent to RAM and can be viewed with the "show
log" command
D. If the "no console loggin" command were configured,
output would besent to a telnet session
E. All of the above
F. None of the above
G. A, B, and C.
H. A, C, D, and E. | | 2 |
| What is the function of the Transport layer and which protocols
reside there?
A.) MAC addressing - IP
B.) Interhost communication - SQL, NFS
C.) Best effort Packet delivery - TCP, UDP
D.) End-to-end connections - TCP, UDP | | 2 |
| Regarding frame relay, which of the following statements are
true?
A.) You must use ANSI encapsulation if connecting to
non-Cisco equipment
B.) You must use IETF encapsulation if connecting to
non-Cisco equipment
C.) You must use Q.933a encapsulation if connecting to
non-Cisco equipment
D.) You must use Cisco encapsulation if connecting to
non-Cisco equipment | | 2 |
| You have an IP host address of 201.222.5.121 and a subnet
mask of 255.255.255.248. What is the broadcast address?
A. 201.222.5.127
B. 201.222.5.120
C. 201.222.5.121
D. 201.222.5.122 | | 1 |
| The PDU at the network layer is a ________
Packet
Frame
Segment
Bit
| | 3 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
