In order to configure a Frame Relay subinterface with IP identify the 2

Advertise your Business Here

Refer this Site

Login | Sign Up


	To Refer this Site to Your Friends Click Here

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

In order to configure a Frame Relay subinterface with IP
identify

the 2 commands that must be configured on the physcial
interface?

A.) Router(config-if)# encapsulation frame-relay

B.) Router(config-if)# no ip address

C.) Router(config-if)#encapsulation subinterface frame-relay

D.) Router(config)# subinterface s0 encapsulation frame-relay

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: In order to configure a Frame Relay subinterface with IP identify the 2 commands that must be configured on the physcial interface? A.) Router(config-if)# encapsulation frame-relay B.) Router(config-if)# no ip address C.) Router(config-if)#encapsulation subinterface frame-relay D.) Router(config)# subinterface s0 encapsulation frame-relay

Answer
# 1

Answer: A B

Is This Answer Correct ?

4 Yes

0 No

Guest

Answer
# 2

To configure sub-interface frame relay, We must enter two
commands in Physical Interface
1. Encapsulation frame-relay
2. No shutdown
{{{Optional}}}
3. No ip address (% This is optional, without this the frame
relay will work)

I configured in GNS3, It works fine without giving " no ip
add" command.

Is This Answer Correct ?

0 Yes

0 No

Sathik Ali

Question	Asked @	Answers
Other CCNA Interview Questions


Which of the following is an example of the Network Layer? A.) Token Ring B.) RARP C.) LLC D.) DDP E.) TCP		1
When configuring the subnet mask for an IP address, which formats can be used?A. dotted-decimal. B. Hexadecimal C. Bit-count D. Octal E. Binary		1
Identify the hardware component that stores the bootstrap program? A.) ROM B.) NVRAM C.) Booter load D.) RAM E.) Flash		2
Identify 3 features of IGRP? A.) Composite metric B.) New horizon C.) Flash updates D.) 60 periodic updates E.) Poison reverse		1
The Internet Protocol (IP) occurs at what layer of the seven layer model? A.) Physical B.) Presentation C.) Network D.) Datalink E.) Session F.) Transport		1
At which layer of the OSI model does the ping command operate? A. session B. network C. transport D. maintenance	jetking	6
What do the following commands accomplish? access-list 1 deny 172.16.4.0 0.0.0.255 access-list 1 permit any interface ethernet 0 IP access-group 1 out A. This will block traffic from subnet 172.16.4.0 and allow all other traffic. B. This will allow traffic from subnet 172.16.4.0 and block all other traffic. C. All traffic is allowed. D. All traffic is blocked.		1
while trouble shooting a network conectivty prob a technician observes that steady link light on the both work stations nic and the switch port which the workstation is conected.however when the ping comand is issuede from the work station the out message is request time out at which layer of osi model does the prob most likly exist 1 sessiom layer protocol layer datalink kayer acess layer network layer application layer i have ansered n/w layer but i am niot sure i have also posted privous question jitendera kumar sinha		3
You have a Frame Relay link on serial 1. Which command displays the Local Management Interface (LMI) data link connection identifier (DLCI) and bandwidth for that link? A. show interface serial1 B. show frame-felay serial1 C. show protocol frame-relay serial1 D. show serial1 encapsulation frame-relay		1
Which layer manages protocol access to the Network layer? A.) Datalink - MAC Sublayer B.) Datalink - LLC Sublayer C.) Transport D.) Session E.) Network		1
Identify the command that displays the SAP table? A.) show ipx servers B.) display SAP table C.) display SAP's D.) show sap table		1
What does the 'S' mean when looking at the routing table? A.) Statically connected B.) Directly connected C.) Dynamically attached D.) Shutdown route		1
Which of the following are examples of the Application Layer? A.) LLC B.) Token Ring C.) Spreadsheet D.) TCP E.) IP F.) Word Processor		1
Which of the following is a connectionless protocol at the Transport layer? A.) UDP B.) ARP C.) ICMP D.) RARP E.) IP F.) FTP		4
Which global configuration command will tell the router to load the IOS file 'IOS_filename' from FLASH memory at the next boot? A.) boot system flash B.) boot system flash IOS_filename C.) boot system IOS_filename flash D.) boot system tftp IOS_filename tftp_address E.) config-register 0x0102 IOS_ filename	HSBC	1
Identify the order of the 5 step encapsulation? 1. Create the segment 2. Convert the frame to bits 3. Create the packet 4. Create the frame 5. User creates the data A.) 1,2,4,2,5 B.) 2,1,3,4,5 C.) 5,1,3,4,2 D.) 5,3,4,1,2		1
If configuring a Cisco router to connect to a non-Cisco router across a Frame Relay network, which encapsulation type would you select? A.) Q933a B.) ISDN C.) IETF D.) CISCO E.) ANSI		1
Which statement is true when a broadcast is sent in an Ethernet/802.3 ITAN? A. The ip shored used is 255.255.255.0 B. The IP address used is 255.255.255.255 C. The MAC address used is 00 00 00 00 00 00 D. The MAC address used is FF FF FF FF FF FF		1
What is the Cisco name for the encapsulation type used on a serial interface? A. HDLC B. SDLC C. SAP D. SNAP		3
A user device that connects to a DCE must be which of the following? A.) DTE B.) CPE C.) Demarc D.) DCE E.) CO		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com