| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| You want a message to be displayed every time someone tries
to log
on to the router. Which command is required to accomplish
this task?
A.) motd#(message)#
B.) banner motd(message)
C.) banner motd#(message)#
D.) banner motd*(message)
E.) banner login#(message)# | | 1 |
| What must you do to test connectivity on a dial on demand
routing (DDR) link?
A. increase the idle Import parameter
B. send interesting traffic across the link
C. reboot one of the integrated services digital network
(ISDN) routers
D. reset the DDR integrated services digital network (ISDN)
router statistics to zero | HCL | 1 |
| What is the default routing metric used by IGRP?
A.) MTU, delay, bandwidth, reliability, and loading
B.) Count to infinity
C.) Bandwidth and delay
D.) Hop count | | 2 |
| Identify 3 features of IGRP?
A.) Composite metric
B.) New horizon
C.) Flash updates
D.) 60 periodic updates
E.) Poison reverse | | 1 |
| Station A is transmitting data to station B faster that
station B
can handle it. When station B's buffer fills up, it send out
a message
to station A to stop sending data. After B empties out its
buffer,
station B sends a message to station A to start sending data
again.
This is most directly an example of (pick the best answer only):
A.) Poison Reverse
B.) Connectionless protocol
C.) Windowing
D.) Connection oriented protocol
E.) Flow Control
F.) Split Horizon | | 1 |
| If you are in IOS user mode, which command do you use to
enter the privileged mode?
A. Set
B. Enable
C. Configure
D. Privileges | | 1 |
| Which layer is responsible for coordinating communication
between
systems?
A.) Application
B.) Network
C.) Session
D.) Transport
E.) Physical
F.) Data Link | HCL | 2 |
| Novell NetWare has an Ethernet frame type called Ethernet_802.2.
What is the matching Cisco command line keyword for this
encapsulation
method?
A.) gns
B.) arpa
C.) snap
D.) sap
E.) novell-ether
F.) dix | | 1 |
| What is the protocol number for TCP?
A.) 80
B.) 21
C.) 11
D.) 6 | | 1 |
| Which of the following is a routing protocols?
TCP
RIP
SMTP
UDP
| | 2 |
| Given the following IP address from the Class C address
range 192.168.21.12. Your network plan needs addresses for
28 small prkps Each office uses its own shored. The
network design specifies that you confound for five bits of
subnetting. When you confound for this in Cisco IOS
software which shored mask should you use?
A. 255.255.0.28
B. 255.255.255.0
C. 255.255.255.28
D. 255.255.255.248
E. 255.255.255.252 | | 1 |
| Which two statements accurately define IP addressing rules?
(Choose two)
A. IP multicast addresses start with 240
B. A host Carbon of all 1 a indicates a network broadcast
C. The value of zero (0) in the host Carbon means all hosts
on the network
D. IP addresses are four octets long and contain a network
Carbon and a host Carbon | | 1 |
| Using the TCP/IP protocol suite, a message is sent from host
A to a destination IP address on the same LAN. How does
host A determine the destination of a MAC address?
A. It uses a proxy APP
B. It uses APP requests
C. It uses PARP requests
D. It uses a router lookup table | | 1 |
| Explain usage of ICMP in IP routing | | 2 |
| What is the function of DDR on Cisco routers?
A. DDR is dial--on-demand routing. It provides a continuous
LAN only
connection.
B. DDR is dial-on-demand routing. It provides routing for
high volume
traffic.
C. DDR is dial--on-demand routing. It provides a continuous
WAN connection.
D. DDR is dial-on-demand routing. It provides routing for
low volume and
periodic traffic. | | 2 |
| Which command displays the intenances using a given access list?
A. show filters
B. show ip interface
C. show active lists
D. show interface paramaters
E. configure ip access lists
F. show access-list interfaces | | 1 |
| Which protocol is used for booting diskless workstations?
A.) IP
B.) ARP
C.) RARP
D.) TCP
E.) SNMP | | 1 |
| What is the maximum hop count for Link-State protocols?
A.) 15
B.) there is no hop count limit
C.) 256
D.) 16 | | 1 |
| Identify the 2 methods to modify the routers boot sequence?
A.) Setup program
B.) Boot system commands
C.) RXBoot
D.) Config-register | | 1 |
| Which configuration task must you complete if a remote Frame
Relay router does NOT support Inverse APP?
A.configure static maps
B.define an IP address locally
C.disable DHCP on the Frame Relay router
D.configure a static route to the remote network | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
