| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which protocol gets a hardware address from a known IP address?
A.) RARP
B.) TCP
C.) IP
D.) BootP
E.) ARP
F.) ICMP | | 3 |
| Identify the command to display the status of the Frame Relay
virtual circuit?
A.) Router# show frame-relay virtual-circuit
B.) Router(config)# show frame-relay pvc
C.) Router# show frame-relay pvc
D.) Router# show virtual | | 1 |
| Identify 2 features of PPP CHAP authentication?
A.) Username and password is sent in clear text
B.) Authentication messages are sent periodically during the
connection
C.) Less secure then PAP
D.) Local router 'challenges' the remote router | | 1 |
| What does the command show access-lists 101 list?
A. all defended access lists
B. all access lists within the router
C. the contents of standard access list 101
D. the contents of defended access list 101 | | 1 |
| what are two security appliances that can be installed a
network | | 7 |
| Access lists are numbered. Which of the following ranges
could be
used for an IP access list?
A. 600 - 699
B. 100 - 199
C. 1 - 99
D. 800 - 899
E. 1000 - 1099 | | 1 |
| Identify the 3 kinds of routes IGRP advertises?
A.) Interior
B.) Dynamic
C.) System
D.) Exterior | | 1 |
| what is bgp, and what its attributes (thanks to sahin he
sende me notes)
Please try to give answer it will help you in future. after
giving the answer most of them i am selected foro\ 2nd round
of interview
thanks | IBM | 1 |
| Which OSI layer provides mechanical, electrical, procedural for
activating, maintaining physical link?
A.) Presentation
B.) Network
C.) Application
D.) Physical
E.) Transport
F.) Data-Link | | 2 |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| You want to clear the outputs on your serial interface
showing errors on the interface. Which command do you type? | | 1 |
| What does the IPX maximum-path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| what is nat.types of nat | | 3 |
| Which command loads a new version of the Cisco IOS into a
router?
A. copy flash ftp
B. copy ftp flash
C. copy flash ftp
D. copy tftp flash | | 1 |
| What are the 3 ways routers learn paths to destination networks?
A.) Dynamic
B.) Static
C.) Routing tables
D.) Default | | 1 |
| What is Spanning Tree Protocol and how it work? I know it
is - STP is Spanning tree Protocol. It Stops the looping in
the network? How STP work? How it stop Looping in network? | | 2 |
| Identify 3 characteristics of ISDN?
A.) Transports voice and data
B.) Transports voice only
C.) Support both BRI and PRI
D.) Runs over existing phone lines
E.) Same as X.25 | | 1 |
| Of the following, which reason applies to dividing a large
network into two or more smaller networks?
Performance
Security
Address Management
All of the above
| | 1 |
| What is the administrative distance for RIP?
A.) 100
B.) 90
C.) 120
D.) 110 | | 3 |
| Identify 2 transport layer protocols?
A.) IP
B.) TCP
C.) CDP
D.) ARP
E.) UDP | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
