| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| what the exact definition of Ethernet.plz reply as soon
soon as possible | | 6 |
| what is the difference between
1 router and switch
2 router and hub
3 hub and switch
4 bridge and switch
| Hathway | 1 |
| raid can be used in?
1 NT
2 Netware
3 all of above
mine answer -NT | | 2 |
| what is native vlan
any one explain
sooraj | | 2 |
| Identify the statement which connects access-list 101 inbound to
interface e0?
A.) Router(config-if)# ip access-group 101 in
B.) Router(config-if)# ip access-group 101
C.) Router(config)# ip access-group 101 e0 in
D.) Router(config)# ip access-group 101 e0 in | | 1 |
| Which command displays the IP addresses assigned to specific
host names?
A. show hosts
B. show interface
C. ping host name
D. config host name
E. show host mapping
F. show host ip address
G. trace ip addresses host name
H. a partridge in a pear tree | | 1 |
| what are loops in switches excactly...and how does it gets
created??? | | 1 |
| What does a router do with a packet that it does not have a
destination
network for?
A.) Sends it to the Serial port
B.) Drops the packet
C.) Sends it back out the same interface it received it in
D.) Forwards the packet to the next hop | | 1 |
| What are the two primary operating modes for frame switching?
A. Full Duplex
B. Half-Duplex
C. CSMA/CD
D. Cut-through
E. Fragmentation
F. Store and Forward
G. User mode
H. Privileged mode | | 1 |
| Which OSI layer performs code conversion, code formatting and
encryption?
A.) Physical
B.) Data-Link
C.) Application
D.) Transport
E.) Presentation
F.) Network | | 1 |
| Which statement is true regarding full duplex?
A.) Allows for transmission and receiving of data simultaneously
B.) Only works in a multipoint configuration
C.) Does not affect the bandwidth
D.) Allows for transmission and receiving of data but not at
the same time | | 1 |
| Which feature of PPP (Point to Point Protocol) allows the router
to bind multiple channels together, to form a single logical
channel?
A.) multi-link ppp
B.) multi-channel ppp
C.) can't be done
D.) omni-ppp
E.) plp | | 1 |
| Which layer is responsible for determining if sufficient
resources
for the
intended communication exists?
A.) Application
B.) Network
C.) Session
D.) Presentation
E.) Transport | | 2 |
| Given the following static route command, 'ip route 3.3.3.0
255.255.255.0
4.4.4.4 125', which portion represents the administrative
distance?
A.) 3.3.3.0
B.) 255.255.255.0
C.) 4.4.4.4
D.) route
E.) 125 | | 2 |
| Which service uses telephone control messages and signals
between
the transfer points along the way to the called destination?
A. Signaling System 7 (SS7)
B. Time-division Multiplexing (TDM)
C. X.25
D. Frame relay | | 1 |
| What is required to support full-duplex Ethernet?
A.) Multiple paths between multiple stations on a link
B.) Automatic sensing operation by all connected stations
C.) Loopback and collision detection disabled
D.) Full-duplex NIC cards | | 1 |
| Identify 1 characteristic of RARP?
A.) MAC to IP address translation
B.) Connectionless delivery of packets
C.) Can be used to initiate remote O/S load sequence
D.) Generates error and control messages | | 3 |
| NetWare IPX addressing uses a network number and a node
number. Which statements are true?
A. The network address is administratively assigned and can
be up to 16 hexadecimal digits long.
B. The node address is always administratively assigned.
C. The node address is usually the MAC address.
D. If the MAC address is used as the node address, then IPX
eliminates the use of ARP. | | 1 |
| What is the default LMI type?
A.) Cisco
B.) ANSI
C.) IETF
D.) Q933a | | 2 |
| What is the command to allow you to type Tokyo instead of the IP
address 172.16.30.1 to access a router named Tokyo?
A.) config t, ip host Tokyo 172.16.30.1
B.) config t, ip hostname Tokyo 172.16.30.1
C.) config t, hostname Tokyo 172.16.30.1
D.) config t, ip hostname 172.16.30.1 Tokyo | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
