| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the 2 commands that will display the status and
information about interface E0 only?
A.) show interface ethernet E0
B.) show interface E0
C.) show E0
D.) show int E0
E.) show interface | | 1 |
| Identify 3 characteristics of IP RIP?
A.) Distance vector
B.) Administrative distance is 120
C.) Periodic updates every 60 seconds
D.) Uses a composite metric
E.) Can load balance | | 1 |
| When discussing static routes, what is the gateway parameter
used
for?
A.) Determining the dynamic route
B.) Defining the subnet
C.) Defining the Administrative Distance
D.) Determining the next hop | | 1 |
| How does the cut-through switching technique work?
A.) By using broadcast address as source addresses
B.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets
C.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
D.) By using a Class I repeater in a collision domain | | 3 |
| Which switching technology can reduce the size of a
broadcast domain?
A.) Cut-Through
B.) Store-and-Forward
C.) Spanning Tree Protocol
D.) RARP
E.) ARP
F.) VLAN | | 1 |
| Identify the 2 types of access-list filters that control SAP
traffic?
A.) Novell-ether
B.) Arpa
C.) Input-sap-filter
D.) Round-robin
E.) Output-sap-filter | | 1 |
| What is the protocol number for TCP?
A.) 80
B.) 21
C.) 11
D.) 6 | | 1 |
| What is the default encapsulation of Netware 3.12?
A.) Ethernet_II
B.) 802.5
C.) 802.2
D.) 802.3 | | 1 |
| In order to limit the quantity of numbers that a system
administrator has to enter, Cisco can use which abbreviation
to indicate
0.0.0.0?
A. host
B. any
C. all
D. include | | 1 |
| Which layer is responsible for determining if sufficient
resources
for the
intended communication exists?
A.) Application
B.) Network
C.) Session
D.) Presentation
E.) Transport | | 1 |
| How do you disable advanced editing?
A.) terminal editing
B.) terminal no editing
C.) disable editing
D.) no terminal editing | | 1 |
| Which layer is responsible for identifying and establishing the
availability of the intended communication partner?
A.) Application
B.) Presentation
C.) Transport
D.) Session
E.) Network | | 1 |
| Which Cisco IOS command should you use to display the Novell
IPX address assignments on a router?
A. show ipx addresses
B. show ipx interface
C. show me the money
D. ipx, network (number)
E. display ipx addresses
F. show ipx routing details | | 1 |
| What does the Spanning Tree Algorithm (STA) do?
A.) Restore lost frames
B.) Builds routing tables for routing through an internetwork
C.) Forward packets through a switch
D.) STA is implemented by STP to prevent loops | | 1 |
| What is the IP extended access list range?
A.) 1000-1099
B.) 100-199
C.) 1-99
D.) 101-200 | | 2 |
| Which command would you type to show SAP and RIP updates you are
receiving on an interface?
A.) sh ipx servers
B.) sh ipx traffic
C.) sh ipx interface
D.) sh ipx route | | 1 |
| Identify the command that specifies Serial 0 in slot 1?
A.) Router(config)# interface serial1/1
B.) Router(config)# interface serial1/0
C.) Router(config)# interface serial0.1
D.) Router(config)# interface serial0/1 | | 3 |
| Which layer is responsible for framing?
A.) Application
B.) Data Link
C.) Physical
D.) Network
E.) Transport | | 2 |
| Which statement about half duplex Ethernet operations is true?
A. With half duplex transmission frames feed into a single
cable in one direction at a time.
B. Half duplex transmission between stations is achieved by
using point to point Ethernet and Fast Ethernet connections
C. Half duplex transmission between stations is achieved by
using point to munificent Ethernet and Fast Ethernet connections
D. Half duplex Ethernet technology provides a transmit
circuit connection wired directly to the receiver circuit at
the other end of the connection | | 5 |
| Identify the statement which connects access-list 101 inbound to
interface e0?
A.) Router(config-if)# ip access-group 101 in
B.) Router(config-if)# ip access-group 101
C.) Router(config)# ip access-group 101 e0 in
D.) Router(config)# ip access-group 101 e0 in | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
