| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| what is the default ad value of the interface directly
coneted to router.
as for exmaple ad value of ospf is 90 then from ehternet
the network is conected whta is difault value of that
directly conected interface.
what is the defalt ad value of bgp
whta is access llist and how many type of access list
what is vlan
what is vpn
how e congigure the router
what is mpls
these are the question skrd to me at tcs i have replyed all
ecxept the first one
| TCS | 1 |
| What is the meaning of PASSIVE interface in RIP, IGRP, EIGRP
& OSPF??
Can any one explain..!!! | | 4 |
| Identify IPX GNS and it's purpose?
A.) Go Network Server - sends a print job to a network server
B.) Get Nearest Server - locate the nearest server
C.) Guaranteed Network Services - allocates resources to users
D.) Get Notes Server - locates Domino Server | | 1 |
| Which layer manages protocol access to the Network layer?
A.) Datalink - MAC Sublayer
B.) Datalink - LLC Sublayer
C.) Transport
D.) Session
E.) Network | | 1 |
| What is the syntax to add a banner to the Cisco router?
A.) motd banner #
B.) banner
C.) banner motd #
D.) banner # | | 1 |
| Which addresses are INCORRECTLY paired with their class?
A. 240 - 255, Class D
B. 240 - 255, Class E
C. 224 - 239, Class D
D. 224 - 239, Class E | | 2 |
| What is the default LMI type for Cisco Routers that are using
Frame-Relay?
A.) Annex D
B.) Q933A
C.) Cisco
D.) IETF
E.) ARPA
F.) Anex A | | 2 |
| Which command would show all Ethernet interfaces with IPX
configured on them?
A.) show interface ipx ethernet
B.) show ipx interface
C.) show ipx interface ethernet
D.) show ipx
E.) show version
F.) show run | | 1 |
| Identify the 3 methods routers learn paths to destinations?
A.) Dynamic routing
B.) None of the above, configured by default
C.) Default routes
D.) Administrative distance
E.) Static routes | | 1 |
| Which layer is responsible for determining if sufficient
resources
for the intended communication exists?
A.) Application
B.) Network
C.) Session
D.) Presentation
E.) Transport | | 1 |
| How can you add the 192.168.100.0/30 network to EIGRP without
involving the
192.168.100.4/30 network as well? | | 3 |
| What are the three phases of PPP session establishment?
A. Link establishment phase
B. Authentication phase
C. Network layer protocol phase
D. Handshake phase
E. Dial-in phase | | 2 |
| Identify the prompt displayed if in privileged exec mode?
A.) Router(config)#
B.) Router#
C.) Router>
D.) Router(priv)# | | 1 |
| Which commands would assign and enable IPX on an interface ?
A.) enable netware
B.) enable novell-ether
C.) router#(config)ipx routing
D.) You must first enable IPX globally and then
assign the network number to the interface .
E.) enable ipx
F.) router#(config-if)ipx network 4a | | 1 |
| Dear Mr. JITENDERA KUAMR SINHA how are and how is your
family? Anyway can u send me your personal email address? | | 4 |
| What is required to support full-duplex Ethernet?
A.) Multiple paths between multiple stations on a link
B.) Automatic sensing operation by all connected stations
C.) Loopback and collision detection disabled
D.) Full-duplex NIC cards | | 1 |
| The benefits to segmenting with Bridges are which of the
following?
A.) Scalability
B.) Datagram filtering
C.) Manageability
D.) Reliability | | 1 |
| How does inter- VLAN communication take place?
A. It takes place through any Cisco router
B. It takes place through a Cisco router that can run ISL
C. It takes place through a router but this disables all the
router a security and filtering functionality for the VLANS
D. For nonroutable protocals (e.g. NetBeui) the router
provides communications between VLAN domains
E. Inter-VLAN communication is not possible because each
VLAN is a separate broadcast domain | | 3 |
| IP standard access lists use which of the following as a
basis for
permitting or denying packets?
A.) destination address
B.) port
C.) protocol
D.) source address | | 1 |
| What would be the proper wildcard mask to permit all odd
numbered hosts on the 10.48.0.0/12 network?
access-list 1 permit 10.48.0.0 0.15.255.255
access-list 1 permit 10.48.0.1 0.15.255.254
access-list 1 permit 10.48.0.0 0.15.255.1
access-list 1 permit 10.48.0.0 0.0.0.254
access-list 1 permit 10.48.0.0 0.0.0.255
| | 5 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
