| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Sequence and acknowledgement numbers are used for?
A.) Layer transitioning
B.) Flow control
C.) Port number addressing
D.) Reliability | | 1 |
| what is the difference between hdlc and ppp protocol | ASD-Lab | 4 |
| Identify the purpose of the Trace command?
A.) Explorer packet transmitting routing information
B.) Test connectivity
C.) Determine the path a packet is taking through the network
D.) Transmits user data when buffers are full | | 2 |
| What IP command would you use to test the entire IP stack?
A.) Stack-test
B.) Arp
C.) Telnet
D.) Ping
E.) Trace | | 1 |
| mention the funtions about connection oriented and
connectionless protocol and how it works ? | | 4 |
| Which layer defines the physical topology?
A.) Application
B.) Transport
C.) Network
D.) Data Link
E.) Physical
F.) Session | | 1 |
| Which port numbers are used by TCP and UDP to set up
sessions with
other hosts?
A.) 1024 and above
B.) 6 and 17 respectively
C.) 1-25
D.) 6-17 | | 2 |
| Which feature of PPP (Point to Point Protocol) allows the router
to bind multiple channels together, to form a single logical
channel?
A.) multi-link ppp
B.) multi-channel ppp
C.) can't be done
D.) omni-ppp
E.) plp | | 1 |
| Identify the 4 that are not LAN technologies?
A.) HDLC
B.) FDDI
C.) 802.5
D.) HSSI
E.) SDLC
F.) Frame Relay | AXA | 1 |
| The Cisco IOS is stored in:
A.) ROM
B.) CD
C.) Flash
D.) NVRAM | | 3 |
| Identify the 3 guidelines for routers in the same autonomous
system?
A.) Must be configured for RIP
B.) Interconnected
C.) Assigned the same autonomous system number
D.) Configured for the same routing protocol
E.) Must be same model of router | | 1 |
| Which 3 statements describe default encapsulation and LMI type
configuration?
A.) There are only 4 encapsulations and 3 LMI type options
B.) The LMI type config term options
C.) In release 11.2 the LMI type is autosensed
D.) The default LMI is Cisco
E.) IETF encapsulation must be configured unless the
connecting routers
are both
Cisco | | 1 |
| What does the IPX maximum-path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| Given the following output, how can we close Telnet session
2? (Choose two)
CCNA2620#show sessions
Conn Host Address Idle Conn Name
1 131.108.100.152 131.108.100.152 0 131.108.100.152
*2 126.102.57.63 126.102.57.63 0 126.102.57.63
❍ A. Press the Enter key and enter exit.
❍ B. Enter disconnect 2.
❍ C. Press the Enter key and enter disconnect 2.
❍ D. Enter close 2. | | 1 |
| Identify the order of the 5 step encapsulation?
1) Create the segment
2) Convert the frame to bits
3) Create the packet
4) Create the frame
5) User creates the data
A.) 1,2,4,2,5
B.) 2,1,3,4,5
C.) 5,1,3,4,2
D.) 5,3,4,1,2 | | 1 |
| Identify 3 Fast Ethernet technologies?
A.) 100 Base FastEther
B.) 100 Base FX
C.) 100 Base T4
D.) 100 Base TX | | 1 |
| What is the default switching method for the Cisco 5000 series?
A.) Cut-through
B.) Store-and-splice
C.) Latency
D.) Store-and-forward | | 1 |
| Which three are typical operational phases in a basic
connection oriented neloyord service? (Choose three)
A. call setup
B. data transfer
C. load balancing
D. call termination
E. call priortization
F. data segmentation
G. data link identification | | 1 |
| Identify IPX SAP and it's purpose?
A.) Sonet Access Pipe - interface to Sonet ring
B.) Service Advertising Protocol - advertise services
C.) Server Appletalk Protocol - appletalk directory services
D.) Service Access Point - identify upper layer protocols | | 1 |
| Which network mask should you place on a Class C address to
accommodate a user requirement for five networks with a
maximum of 17 hosts on each networks
A. 255.255.255.192
B. 255.255.255.224
C. 255.255.255.240
D. 255.255.255.248 | | 7 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
