| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the command to configure the router for IGRP autonomous
system 100?
A.) Router(config)# router igrp 100
B.) Router> router igrp 100
C.) Router# router igrp 100
D.) Router(config)# router igrp | CMS | 2 |
| Which feature of PPP (Point to Point Protocol) allows the router
to bind multiple channels together, to form a single logical
channel?
A.) multi-link ppp
B.) multi-channel ppp
C.) can't be done
D.) omni-ppp
E.) plp | | 1 |
| You have a Frame Relay link on serial 1. Which command
displays the Local Management Interface (LMI) data link
connection identifier (DLCI) and bandwidth for that link?
A. show interface serial1
B. show frame-felay serial1
C. show protocol frame-relay serial1
D. show serial1 encapsulation frame-relay | | 1 |
| Identify the default encapsulation on serial interfaces?
A.) ISDN
B.) HDLC
C.) SDLC
D.) Frame Relay
E.) PPP | | 1 |
| Given an IP host address of 172.16.2.160 and a shored mask
of 255.255.255.192 to which shored does the host belong?
A. 172.16.2.32
B. 172.16.2.64
C. 172.16.2.96
D. 172.16.2.128
E. 172.16.2.192 | | 2 |
| Identify the command to configure the router to boot from an
alternate IOS located in flash?
A.) boot system flash IOS.exe
B.) boot system tftp IOS.exe 172.16.5.1
C.) boot system alternate IOS.exe
D.) boot system rom IOS.exe | | 1 |
| What is the administrative distance for RIP?
A.) 100
B.) 90
C.) 120
D.) 110 | | 4 |
| Which type of switching is considered to be 'wire speed?'
A.) Cut-Through
B.) Multiplexed
C.) Inverted
D.) Layer 4
E.) Store and Forward
F.) Layer 3 | | 1 |
| Which of the following are characteristics of UDP?
A.) UDP is connection oriented.
B.) UDP is used with TFTP.
C.) UDP is unreliable.
D.) UDP is connectionless.
E.) UDP is at the transport layer.
F.) UDP uses no acknowledgements. | | 1 |
| Given an IPX network with redundant paths, what command will
configure load balancing?
A.) ipx load-balance
B.) ip maximum-paths 2
C.) ipx maximum-paths 2
D.) ipx load-share | | 1 |
| Which protocol will send a message to routers if a network
outage
or congestion occurs?
A.) ARP
B.) TCP
C.) IP
D.) ICMP | | 1 |
| Which OSI Reference Layer controls application to application
communication?
A.) Datalink
B.) Network
C.) Transport
D.) Session
E.) Physical | | 1 |
| Given the global configuration command 'banner motd #7 Hello #',
what do the '#' symbols represent?
A.) Escape sequence to exit the menu.
B.) Nothing, just part of the banner.
C.) Tic Tac Toe Macro.
D.) Delimiting Character
E.) Message border character.
F.) Number of times message to be displayed. | | 1 |
| Hi Guys
I am facing one problem while configuring PAP over Point to
Point links. Configuration scenario is like this.
ROUTER 1: (Hostname – R1)
R1(config)#username R2 password CCNA2
R1(config)#interface serial 1/1
R1(config-if)ip address 10.0.0.1 255.0.0.0
R1(config-if)#lock rate 64000
R1(config-if)#encapsulation ppp
R1(config-if)#ppp authentication pap
R1(config-if)#ppp pap sent –username R1 password CCNA1
R1(config-if)#no shutdown
ROUTER 2: (Hostname – R2)
R2(config)#usename R1 password CCNA1
R2(config)#interface serial 1/1
R2(config-if)#ip address 10.0.0.2 255.0.0.0
R2(config-if)#encapsulation ppp
R2(config-if)# ppp authentication pap
R2(config-if)# ppp pap sent –username R2 password CCNA2
R2(config-if)#no shutdown
Now problem is that, after configure the command “ppp
authentication pap” the “Line protocol” status goes down on
each router. But when I disable this command using “no ppp
authentication pap”, the “Line Protocol” status goes up.
What could be the problem, can anyone explain it plzzz….!!!
Thanks in Advance…!!
Shahin..
| | 6 |
| What ISDN protocol specifies concepts, terminology, and
services?
A.) Q
B.) S
C.) I
D.) E | | 1 |
| What is a back off on an 802.3 networks?
A. It is latency in store and forward switching
B. It is the time used for token passing from machine to machine
C. It is the retransmission delay that is enforced when a
collision occurs
D. It is the result of two nodes transmitting at the same
time. The frames from each transmitting device collide and
are damaged | | 1 |
| 1 whatis te1,te2 and nt1 what is threre functions
2 what are the isdn protocols
3 whait is spid | | 1 |
| What is the maximum number of subnets that can be assigned
to networks when using the address 172.16.0.0 with a subnet
mask of 255.255.240.0? (Assume older version UNIX
workstations are in use.)
A. 16
B. 32
C. 30
D. 14
E. It is an invalid subnet mask for the Network. | | 1 |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| Select the correct statements about PPP and SLIP for WAN
communications?
A. PPP uses its Network Control Programs (NCPs) component to
encapsulate
multiple protocols.
B. PPP can only transport TCP/IP
C. SLIP can only transport TCP/IP.
D. SLIP uses its Network Control Programs (NCPs) component to
encapsulate multiple protocols. | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
