| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following are valid Cisco encapsulation type names?
A.) arpa = IPX Ethernet
B.) novell-ether = IPX Ethernet_802.3
C.) snap = IEEE 802.2 SNAP on Ethernet, FDDI, and Token Ring
D.) novell-fddi = IPX Fddi_Raw
E.) sap = IEEE 802.2 on Ethernet, FDDI, and Token Ring
F.) hdlc = HDLC on serial interfaces | | 1 |
| Which of the following is an invalid host address using a
netmask
of 255.255.255.192?
A.) 10.1.1.1
B.) 10.1.1.66
C.) 10.1.1.130
D.) 10.1.1.127 | | 1 |
| Which protocol gets a hardware address from a known IP address?
A.) RARP
B.) TCP
C.) IP
D.) BootP
E.) ARP
F.) ICMP | | 1 |
| Identify the purpose of the Trace command?
A.) Explorer packet transmitting routing information
B.) Test connectivity
C.) Determine the path a packet is taking through the network
D.) Transmits user data when buffers are full | | 1 |
| Which show command should you use to view Frame Relay Local
Management Interface (LMI) Frame statistics?
A. show lmi
B. show ip route
C. show interface
D. show statistics
E. show frame-relay lmi | | 1 |
| Identify the 4 that are WAN technologies?
A.) HDLC
B.) FDDI
C.) 802.5
D.) HSSI
E.) SDLC
F.) Frame Relay | | 2 |
| What is a back off on an 802.3 networks?
A. It is latency in store and forward switching
B. It is the time used for token passing from machine to machine
C. It is the retransmission delay that is enforced when a
collision occurs
D. It is the result of two nodes transmitting at the same
time. The frames from each transmitting device collide and
are damaged | | 1 |
| which of the following address represent unicast address
A 224.1.5.2
B ffff.ffff.ffff.ffff
C 192.168.24.59/30
D 255.255.255.255
E 172.138.128.255
plz tell what should be answer plz tell with explanation
| IPsoft | 3 |
| What should be the first command to create an access-list that
prevents all users on subnetwork 10.10.128.0, using subnet mask
255.255.192.0, from being
able to telnet anywhere?
A.) access-list 101 deny tcp 10.10.128.0 0.0.63.255 any eq
telnet
B.) access-list 101 deny tcp 10.10.128.0 255.255.0.0 any eq
telnet
C.) access-list 101 deny tcp 10.10.128.0 255.255.192.0 any
eq telnet
D.) access-list 101 deny tcp 10.10.128.0 0.0.192.255 any eq
telnet
E.) access-list 101 deny tcp 10.10.128.0 0.0.128.255 any eq
telnet
F.) access-list 101 deny tcp 10.10.128.0 0.0.127.255 any eq
telnet | | 3 |
| A traffic light is an example of what type of mechanism?
A.) Collision detection
B.) Flow control
C.) Sequence numbering
D.) Network management | | 1 |
| What information can you get from CDP info: (choose all that
apply)
A.) Hardware platform
B.) One address per protocol
C.) Software platform
D.) Hostname
E.) The same info as show version
F.) Incoming/outgoing port | | 1 |
| Which protocol resolves an IP address to a MAC address?
A.) DHCP
B.) RARP
C.) ARP
D.) NBP
E.) DNS | | 3 |
| Identify 3 features of IGRP?
A.) Composite metric
B.) New horizon
C.) Flash (triggered) updates
D.) 60-second periodic updates
E.) Poison reverse | | 1 |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| (1)what is "rtp" and how it work,
(2)what is diffrence between igrp and eigrp
(3)the slection prcedure of dr and bdr is depend open
(4)why frame really is called nbma
(5)what is ppp
(6) what is diffrence b/w tcp and udp
(7) how can we implement ospf protocall on any router
(8)whta is as nomber
(9)what is AD value
(10)what is the broadcast id,n/w id and number of vallid
host of the 255.255.255.128/25 195.168.10.10/25
(11) what is stub network
(12) what is contigues n/w
(13)on which type of router we can implement default routing
(14)what is diffrence b/w hub switch;switch router,
(15)what is v lan
(16)what is the diffrence b/w link sate protocal and
distance vector protocall
(17)what is synchoransh mode of data transfer and
asynchronash mode of data transfer
(18) question on lab,
belive me frnds there are 20 questions and 5 questions on
lab implimentaion.around 1.1/2 hour i was in interview room
and after givieng 17 right answera and 4 in lab i got
slected
try to give answer
if any difficulty or any prob plz email me on
jitenderasinha.it@gmail.com
if any one of you havae boson netsim plz also intimate me
| | 4 |
| Which of the following are valid Cisco encapsulation type names?
A.) arpa = IPX Ethernet
B.) novell-ether = IPX Ethernet_802.3
C.) snap = IEEE 802.2 SNAP on Ethernet, FDDI, and Token Ring
D.) novell-fddi = IPX Fddi_Raw
E.) sap = IEEE 802.2 on Ethernet, FDDI, and Token Ring
F.) hdlc = HDLC on serial interfaces | | 1 |
| What is the difference between OSPF Exteral Type 1 (O E1) &
External Type 2 (O E2) routes???? | | 3 |
| here is your question sahin
Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight
is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1,
K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP.
I knew about it from ICND 2 cisco press book.
Three more questions -
a) If we change the K value (I mean metric weight)on a
router what will happen???
b) When redistribution is necessary in EIGRP. Is there any
condition for that???
c) What is reference bandwidth for metric calculation in
EIGRP. As we know, in OSPF, on a CISCO router reference
bandwidth is 10Mbps. | | 3 |
| What is the bit length and expression form of a MAC address?
A. 24 bits expressed as a decimal number
B. 24 bits expressed as a hexadecimal number
C. 36 bits expressed as a binary number
D. 48 bits expressed as a decimal number
E. 48 bits expressed as a hexadecimal number | | 2 |
| Which two does 100BaseT use?
A.) CSMA/CD
B.) IEEE 802.5
C.) 802.3u
D.) Switching with 53-byte cells | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
