| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the command that forces the router to load into ROM
mode
upon a reload?
A.) boot system rom
B.) rom boot
C.) boot system flash rom
D.) boot router rom | | 1 |
| Identify the protocol to test connectivity without
configuring any
layer 3
protocols?
A.) TCP
B.) Ping
C.) IP
D.) CDP
E.) Telnet | | 1 |
| Identify the 3 kinds of routes IGRP advertises?
A.) Interior
B.) Dynamic
C.) System
D.) Exterior | | 1 |
| What is the default encapsulation of Netware 3.12?
A.) Ethernet_II
B.) 802.5
C.) 802.2
D.) 802.3 | | 1 |
| The PDU at the network layer is a ________
Packet
Frame
Segment
Bit
| | 3 |
| Which of the following would not be displayed by the command
?sho cdp
neighbor detail??
A.) The incoming/outgoing interface.
B.) The hardware platform.
C.) One address per protocol.
D.) Amount of Flash Memory Available
E.) The routers hostname.
F.) The subnet mask, if IP is configured. | | 1 |
| What is the IP extended access list range?
A.) 1000-1099
B.) 100-199
C.) 1-99
D.) 101-200 | | 3 |
| why we give clock rate to DCE and not to DTE
what is the difference in the two. | | 2 |
| Which command sets IGRP as the routing protocol for
autonomous system 100?
A. Router(config)#igrp 100
B. Router(config)#network 100
C. Router(config)#router igrp 100
D. Router(config)#enable igrp 100 | | 1 |
| Which of the following are ways to provide login access to a
router?
A.) HTTP
B.) Console
C.) Telnet
D.) Aux Port
E.) SNMP
F.) LLC | | 1 |
| what is the boot seqance of cisco router | | 5 |
| Which IP Address Class is INCORRECTLY paired with its range
of network numbers?
A. Class A addresses include 192.0.0.0 through 223.255.255.0
B. Class A addresses include 1.0.0.0 through 126.0.0.0
C. Class B addresses include 128.0.0.0 through 191.255.0.0
D. Class C addresses include 192.0.0.0 through 223.255.255.0
E. Class D addresses include 224.0.0.0 through 239.255.255.0 | | 3 |
| CPE is an acronym for which of the following?
A.) Customer Premise Equipment
B.) Central Processing Engineering
C.) Customer Process Equipment
D.) Central Processing Equipment | | 2 |
| What is true when using DDR?
A.) HDLC is the preferred encapsulation
B.) You must use static routing
C.) You should use dynamic routing
D.) You should use ISDN | | 1 |
| let there are three switch and there are 3 ree valn craed
on each switch that is vlan 2 on first switch valn 3 on 2nd
switch and vlan 4 is cretaed on switch 3
i have implemnted intervlan routin through ciso switchses.
the router is conected through its fa0/1 port by one switch
and and the two switch are trunked with each other
now question is that we want to comuniacte betwwen vlan but
does alse want that only vlan 2 is allow to access internet
(ISP)which is conected through s0 interface of router.and
no any vlan can access that internet.what should be
solution. | | 1 |
| Identify 3 characteristics of ISDN?
A.) Transports voice and data
B.) Transports voice only
C.) Support both BRI and PRI
D.) Runs over existing phone lines
E.) Same as X.25 | | 1 |
| Where is the point between the customers site and the phone
carrier that responsibility changes?
A.) CO
B.) Demarc
C.) DCE
D.) DTE
E.) CPE | | 1 |
| Which two of the following protocols are used at the
Transport layer?
A.) ARP
B.) UDP
C.) ICMP
D.) RARP
E.) TCP
F.) BootP | | 1 |
| what is burst rate | ASD-Lab | 1 |
| take a pen and copy before solving that question
there is a router name Ra
there is two switch sw1 and sw2
sw1 is coneceted through fa0/1 interface of router Ra
sw2 is conected through the fa1/1
serai interface of router s0/1 conected through the isp
with it ip address 192.168.1.1
now therer are three host conexted through the sw1 and
having ip
host1=10.1.2.1
host2=10.1.2.2
host3=10.1.2.3
now there is also 3ree host conected through switch 2 i.e
sw2 having ip
host4=10.1.1.1
host 5=10.1.1.2
host 6=10.1.1.3
now i think u have made corect confrigation.now questios is
started
network admin configure the Ra router in that fassion
Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255
Ra(config)#line vty 0 4
ra(config)#access-class 2 in
now question is that why should network admnistratoe do it
in this maneer
A to give access sw1 host to acess internet
B to prevent sw1 host from acessing comand promt
c to prevent sw2 host from accessing console of router ra
D to give sw2 host access to the enternet
e prevent sw1 host from accessing internet
f to prevent sw1 host from acessing the sw2 host network
isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6)
|
|
(sw1)------host 1,2,3
this is not exect digarm but help to derive the diagram
plz answer as soon as possible
| AT&T | 6 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
