| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify 3 methods used to prevent routing loops?
A.) Split horizon
B.) Holddown timers
C.) Poison reverse
D.) SPF algorithm
E.) LSP's | | 2 |
| Which port numbers are used by TCP and UDP to set up
sessions with
other hosts?
A.) 1024 and above
B.) 6 and 17 respectively
C.) 1-25
D.) 6-17 | | 2 |
| Identify the 3 characteristics of IGRP?
A.) Uses hop count as a metric
B.) Supports multiple unequal paths
C.) Administrative distance is 100
D.) Configured with an Automous system number
E.) Link state | | 1 |
| What is the default LMI type?
A.) Cisco
B.) ANSI
C.) IETF
D.) Q933a | | 2 |
| Identify the command to display the Frame Relay map table?
A.) Router# display frame-relay map
B.) Router# show frame-relay map
C.) Router(setup)# show frame-relay map
D.) Router# show map frame-relay | | 1 |
| Given the global configuration command 'banner motd #7 Hello #',
what do the '#' symbols represent?
A.) Escape sequence to exit the menu.
B.) Nothing, just part of the banner.
C.) Tic Tac Toe Macro.
D.) Delimiting Character
E.) Message border character.
F.) Number of times message to be displayed. | | 1 |
| What are two ways IPX supports multiple logical networks on
an individual underrate? (Choose two)
A. network number
B. routing protocol
C. encapsulation type
D. autonomous system number | | 1 |
| Station A is transmitting data to station B faster that
station B
can handle it. When station B's buffer fills up, it send out
a message
to station A to stop sending data. After B empties out its
buffer,
station B sends a message to station A to start sending data
again.
This is most directly an example of (pick the best answer only):
A.) Poison Reverse
B.) Connectionless protocol
C.) Windowing
D.) Connection oriented protocol
E.) Flow Control
F.) Split Horizon | | 1 |
| what is farme realy.and on which layer it work | | 1 |
| there is three mode of vtp let there are three switch s1 in
server mode s2 in transparent mede and s3 in clint mode
then will that tranparnt mode going to effect the network if
yes then how and if no then what it will do | IBM | 1 |
| What does a metric of 16 hops represent when using RIP?
A.) Number of hops to the destination
B.) Destination unreachable
C.) Number of routers
D.) Bandwidth | IBM | 2 |
| Which of the following is an example of the Session Layer?
A.) TCP
B.) SQL
C.) IP
D.) X-Windows
E.) Token Ring
F.) LLC | | 2 |
| What is true when creating static route?
A.) The mask parameter is optional
B.) The administrative distance is required
C.) The gateway parameter is required
D.) The administrative distance is optional | | 1 |
| Given the IPX address 4a.0002.1111.a999, what is the network ID
and what is the node ID?
A.) net 4a host 0002.1111.a999
B.) net a999 node 0002.1111
C.) net 0002.1111.a999 node 4a
D.) net 0002.1111 node a999 | | 1 |
| What is the default LMI type for Cisco Routers that are using
Frame-Relay?
A.) Annex D
B.) Q933A
C.) Cisco
D.) IETF
E.) ARPA
F.) Anex A | | 2 |
| Given an IPX network with redundant paths, what command will
configure load balancing?
A.) ipx load-balance
B.) ip maximum-paths 2
C.) ipx maximum-paths 2
D.) ipx load-share | | 1 |
| Identify the effect of Ctrl-Z?
A.) Exits back to privileged exec mode
B.) Disconnect from the router
C.) Abort the ping operation
D.) Exits privileged exec mode | | 2 |
| In the setup dialog, what do the square brackets indicate?
A. current or default spores
B. hard coded values that cannot be modified
C. values entered by the administrator but not saved
D. values that must be written to NVRAM before becoming enabled | | 1 |
| What is the default size of a standard ping on a Cisco router?
* A: 100 bytes
* B: 32 bytes
* C: 10 bytes
* D: 16 bytes
| CMS | 2 |
| Which three statements about Frame Relay configurations
using subinterfaces is true? (Choose three)
A. Each subinterface is conferred either multipoint or point
to point
B. Any network address must be removed from the physical
interface
C. The configuration of subinterfaces is done in router
(config-if)# mode
D. Frame Relay encapsulation must be conferred on each
subinterface | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
