| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Dear Mr. JITENDERA KUAMR SINHA how are and how is your
family? Anyway can u send me your personal email address? | | 4 |
| In order to configure a Frame Relay subinterface with IP
identify
the 2 commands that must be configured on the physical
interface?
A.) Router(config-if)# encapsulation frame-relay
B.) Router(config-if)# no ip address
C.) Router(config-if)#encapsulation subinterface frame-relay
D.) Router(config)# subinterface s0 encapsulation frame-relay | | 1 |
| Which OSI layer provides best effort end to end packet delivery?
A.) Data-Link
B.) Presentation
C.) Network
D.) Transport
E.) Physical
F.) Application | | 1 |
| The Datalink layer works with which of the following:
A.) Packets
B.) Bits
C.) Globules
D.) Frames
E.) Segments | | 1 |
| Which statement about half duplex Ethernet operations is true?
A. With half duplex transmission frames feed into a single
cable in one direction at a time.
B. Half duplex transmission between stations is achieved by
using point to point Ethernet and Fast Ethernet connections
C. Half duplex transmission between stations is achieved by
using point to munificent Ethernet and Fast Ethernet connections
D. Half duplex Ethernet technology provides a transmit
circuit connection wired directly to the receiver circuit at
the other end of the connection | | 5 |
| IP extended access lists use which of the following as a
basis for
permitting or denying packets?
A.) destination address
B.) all of the above
C.) protocol
D.) source address
E.) port | | 1 |
| what is the difference between hdlc and ppp protocol | ASD-Lab | 4 |
| You have two Cisco routers setup back-to-back in a lab using
DTE/DCE cables. To which router would you add the clockrate
command?
A.) The serial port on the DCE router
B.) The Ethernet port on the DTE router
C.) The Ethernet port on the DCE router
D.) The serial port on the DTE router | TCS | 3 |
| Which ISDN protocol prefix specifies switching and signaling?
A.) I
B.) E
C.) Q
D.) S | | 1 |
| Given an IPX network with redundant paths, what command will
configure load balancing?
A.) ipx load-balance
B.) ip maximum-paths 2
C.) ipx maximum-paths 2
D.) ipx load-share | | 1 |
| What are characteristics of UDP
A. It is reliable and acknowledged
B. It is unreliable and acknowledged
C. It is reliable and unacknowledged
D. It is unreliable and unacknowledged | | 2 |
| Hi, Jitendra thanks for giving me answer of intervlan
routing. it helps me to clear my concepts. Actually I am
appearing for CCNA globel Certification exam in next month
can some provides me tips for preparing exams. for ex.
Notes, dumps on my email. umesh.pede402@gmail.com | | 3 |
| Identify the correct IGRP configuration?
A.) Router# router igrp 100
Router# network 10.0.0.0
B.) Router(config)#router igrp 100
Router(config-router)#network 10.0.0.0
C.) Router(config)# router igrp
Router(config-router)# network 10.0.0.0 | | 2 |
| Which of the following is true?
A. The default is to send debug output to the console screen.
B. To view debug output from a telnet session, the "terminal
monitor" command must be used
C. If the "logging buffered" command is used, the debug
output would be sent to RAM and can be viewed with the "show
log" command
D. If the "no console loggin" command were configured,
output would besent to a telnet session
E. All of the above
F. None of the above
G. A, B, and C.
H. A, C, D, and E. | | 2 |
| Which three protocols are corerectly matched to their
transport layer functions? (Choose three)
A. route selection IP
B. sliding window UDP
C. well known pods IP
D. route validation ICMP
E. connection oriented TCP
F. three way handshake TCP
G. no sequence and acknowledgement UDP | | 1 |
| What is true when using DDR?
A.) HDLC is the preferred encapsulation
B.) You must use static routing
C.) You should use dynamic routing
D.) You should use ISDN | | 1 |
| Which of the following describe SMTP?
A.) Used for downloading files to the router.
B.) Used for sending e-mail.
C.) Uses TCP.
D.) Uses UDP.
E.) Uses port 25.
F.) Used for managing IP devices. | | 1 |
| Which two commands allow you to verify address configuration
in your unternetword? (Choose two)
A. ping
B. trace
C. verify
D. test ip
E. Echo ip
F. config ip | | 2 |
| What are two characteristics of the RARP protocol? (Choose two)
A. it generates parameter problem messages
B. it maps IP addresses to Ethernet addresses
C. it maps Ethernet addresses to IP addresses
D. it is implemented directly on top of the data link layer | | 1 |
| At which layer of the OSI model does the ping command operate?
A. session
B. network
C. transport
D. maintenance | jetking | 6 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
