Based upon the exhibit, create a static route to 172.16.10.0 on Router A

Advertise your Business Here

Refer this Site

Login | Sign Up


	Ask Questions on ANYTHING, that arise in your Daily Life at FORUM9.COM

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

Based upon the exhibit, create a static route to 172.16.10.0 on

Router A

A.) Router# ip route 172.16.10.0 255.255.255.0 10.1.0.2

B.) Router(config)# ip static route 172.16.10.0
255.255.255.0 10.1.0.2

C.) Router(config)# ip route 172.16.10.0 10.1.0.2

D.) Router(config)# ip route 172.16.10.0 255.255.255.0 10.1.0.2

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: Based upon the exhibit, create a static route to 172.16.10.0 on Router A A.) Router# ip route 172.16.10.0 255.255.255.0 10.1.0.2 B.) Router(config)# ip static route 172.16.10.0 255.255.255.0 10.1.0.2 C.) Router(config)# ip route 172.16.10.0 10.1.0.2 D.) Router(config)# ip route 172.16.10.0 255.255.255.0 10.1.0.2

Answer
# 1

Answer: D

Is This Answer Correct ?

0 Yes

0 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


What does the IPX maximum-path command do? A.) Allows you to disable the TTL on an IPX packet B.) This parameter is only used in NLSP routing C.) Sets the maximum metric that can appear in the routing table D.) Configures round robin load sharing over multiple equal metric paths (parallel paths)		1
What does a Standard IP Access-list use as test criteria? A.) IP source address B.) IP source and destination address, protocol numbers and port numbers C.) IPX source and destination address D.) Source MAC address		1
Which three types of connectors are commonly associated with Cisco's V.35 serial cables? (Choose three.) 0 RJ 11 1 DB 60 2 Winchester 15 pin 3 DB 9 4 smart serial 5 RJ 45		3
In regards to the ISDN BRI standard, which channel is used for control? A.) B B.) D C.) E D.) I E.) Q		1
Identify the 2 commands to copy a configuration from a TFTP server to RAM? A.) configure network B.) configure overwrite C.) copy backup-config running-config D.) copy tftp running-config		1
Given the global configuration commands: 'banner motd #' 'Hello #' When would the message be displayed? A.) The message of the day banner shows up before login. B.) The message of the day banner shows up during logoff. C.) These commands are not the right syntax for MOTD. D.) Message of the day banners are displayed upon entering global config mode. E.) Message of the day banners are not possible. F.) The message of the day would be, 'Hello #'		1
As a system administrator, you need to set up one Ethernet interface on the Cisco router to allow for both sap and Novell-ether encapsulations. Which set of commands will accomplish this? A. interface ethernet 0.1 ipx encapsulation Novell-ether ipx network 9e interface ethernet 0.2 ipx network 6c B. interface ethernet 0 ipx encapsulation Novell-ether ipx network 9e interface ethernet 0 ipx encapsulation sap ipx network 6c C. interface ethernet 0.1 ipx encapsulation Novell-ether interface ethernet 0.2 ipx encapsulation sap D. interface ethernet 0.1 ipx encapsulation Novell-ether ipx network 9e interface ethernet 0.2 ipx encapsulation sap ipx network 6c		1
What is Cisco register bits? How they help?	jetking	1
Given the command 'cl?', what will it display? A.) Syntax of the 'clock' command B.) Syntax of the 'clear' command C.) All commands that begin with 'cl' D.) All commands that begin with 'c'		2
Identify the command to display the status of the Frame Relay virtual circuit? A.) Router# show frame-relay virtual-circuit B.) Router(config)# show frame-relay pvc C.) Router# show frame-relay pvc D.) Router# show virtual		1
what is diffrence between circit switching and packet switching	Volvo	1
If you are running Token Ring with Novell IPX routing, which encapsulation should you use? A.) SAP B.) SNAP C.) 802.5 D.) 802.2		1
Which ISDN protocol prefix specifies switching and signalling? A.) I B.) E C.) Q D.) S		1
Identify 3 Fast Ethernet technologies? A.) 100 Base FastEther B.) 100 Base FX C.) 100 Base T4 D.) 100 Base TX		1
Which is true regarding store-and-forward switching method? A.) Latency varies depending on frame-length B.) Latency is constant C.) It is default for all Cisco switches D.) It only reads the destination hardware address before forwarding the frame		1
raid can be used in? 1 NT 2 Netware 3 all of above mine answer -NT		2
Which two solutions are used to reduce the chance of distance vector routing loops? (choose two) A. split horizon B. route poison C. area hierarchies D. link state algorithms		1
In order to limit the quantity of numbers that a system administrator has to enter, Cisco can use which abbreviation to indicate 0.0.0.0? A. host B. any C. all D. include		1
what is route aggregation		2
Identify the 3 methods routers learn paths to destinations? A.) Dynamic routing B.) None of the above, configured by default C.) Default routes D.) Administrative distance E.) Static routes		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com