| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| How we put NIC in promiscuous mode when using MS windows,
can any one tell me in detail | Cisco | 1 |
| The Cisco Catalyst 5000 switch supports full duplex. How
would you
enable it on the second port of the card in slot 1?
A.) router(config-if)# duplex full
B.) router(config)# duplex full
C.) router(config-if)# set port duplex
D.) router(config)#port duplex = full
E.) router(config-if)# set port 1/2 full | | 1 |
| Which range of possible numbers do standard ipx access lists
have?
A. 100 199
B. 600 699
C. 800 899
D. 1000-1099 | | 1 |
| Which layer is responsible for routing through an internetwork?
A.) Physical
B.) Session
C.) Network
D.) Transport
E.) Application
F.) Data Link | | 1 |
| How does a switch use store and forward?
A.) By using a Class I repeater in a collision domain
B.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
C.) By using broadcast addresses as source addresses
D.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets | | 1 |
| Given the configuration example<HR>
<B>interface ethernet0
ipx network 4a
ipx access group 800 out
interface ethernet1
ipx network 3d
interface ethernet2
ipx network 5c
access list 800 permit 3d 4a</B><HR>
Which two actions result from implementing this
configuration? (Choose two)
A. IPX network 5c will not receive any traffic
B. Traffic from network 3d for network 4a will be forwarded
out e0
C. Traffic from network 4a for network 3d will be forwarded
out e0
D. Traffic from network 3d destined for network 4a will be
forwarded out e2
E. The access list is applied to an outgoing interface and
filters outbound traffic | | 1 |
| What is the Difference between Hub and Switch? | | 2 |
| What is the maximum hop count for Link-State protocols?
A.) 15
B.) there is no hop count limit
C.) 256
D.) 16 | | 1 |
| Which global configuration command will tell the router to load
the IOS file 'IOS_filename' from FLASH memory at the next boot?
A.) boot system flash
B.) boot system flash IOS_filename
C.) boot system IOS_filename flash
D.) boot system tftp IOS_filename tftp_address
E.) config-register 0x0102 IOS_ filename | HSBC | 1 |
| Your PC has been configured with IP Address 192.168.3.25
and a subnet mask of 255.255.255.0. Which of the following
IP Addresses is a valid default gateway address for your
PC?
192.168.3.0 255.255.255.0
192.168.3.2 255.255.255.0
192.168.3.25 255.255.255.0
192.168.4.1 255.255.255.255
| | 1 |
| Identify the 3 Internet layer IP protocols?
A.) NetBios
B.) IPX
C.) ARP
D.) IP
E.) RARP | | 1 |
| Hi,can anyone explain me in brief about ccna security.
waiting for your answer | | 2 |
| Identify the command that displays traffic statistics on
serial0/1?
A.) display interface serial0/1
B.) show interface serial0/1
C.) show seria0/1 stats
D.) show interface serial0/1 stats | | 1 |
| Identify the switching method that receives the entire frame
then
dispatches it?
A.) Cut-through
B.) Receive and forward
C.) Store and forward
D.) Fast forward | | 1 |
| What is the maximum hop count for Link-State protocols?
A.) 15
B.) there is no hop count limit
C.) 256
D.) 16 | | 1 |
| What is the IEEE specification for Spanning Tree Protocol?
A.) 802.9
B.) 803.ud
C.) 803
D.) 802.1d | | 1 |
| What are the generic parts of a network layer address?
A. an intenetworks number and a URL
B. a vendor code and a serial number
C. a network number and a host number
D. a broadcast number and a unicast number
E. a domain identifier and a device identifier | | 1 |
| Identify the 2 characteristics regarding MAC addresses?
A.) Contains a network portion and host portion
B.) Always assigned by System Administrator
C.) 48 bits long
D.) Contains a vendor code and serial number | | 1 |
| What are the two most common transport layer protocols?
UDP
TCP
IPX
ARP
| | 2 |
| What does a Standard IP Access-list use as test criteria?
A.) IP source address
B.) IP source and destination address, protocol numbers and
port numbers
C.) IPX source and destination address
D.) Source MAC address | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
