| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What command would show the version of the IOS that you are
running?
A.) show nvram
B.) show version
C.) show startup-config
D.) show ios
E.) ver -a
F.) show ram | | 1 |
| Which command would show all Ethernet interfaces with IPX
configured on them?
A.) show interface ipx ethernet
B.) show ipx interface
C.) show ipx interface ethernet
D.) show ipx
E.) show version
F.) show run | | 1 |
| Which of the following protocols are used for logical network
addressing?
A.) IP
B.) TCP
C.) ARP
D.) ICMP
E.) RARP
F.) BootP | | 3 |
| Which three devices can be used to convert the user data
from the
DTE into a form acceptable to the WAN service's facility?
A. Modem
B. CSU/DSU
C. TA/NT1
D. CO
E. SS7 | | 1 |
| You have a Class B network address divided into 30 subnets. You
will add 25 new subnets within the next year. You need 600
host IDs for
each subnet.
Which subnet mask should you use?
A.) 255.254.0.0
B.) 255.192.0.0
C.) 255.255.252.0
D.) 255.255.248 0 | | 1 |
| Which of the following are examples of the Transport Layer?
A.) SQL
B.) UDP
C.) IP
D.) LLC
E.) ARP | | 1 |
| What is the default encapsulation and frame type on an Ethernet
interface
when enabling Novell?
A.) SNAP
B.) Ethernet_II
C.) 802.2
D.) 802.3
E.) SAP
F.) Novell-ether | | 1 |
| Which network mask should you place on a Class C address to
accommodate a user requirement of two subnetworks with a
maxximum of 35 hosts on each networks
A. 255.255.255.192
B. 255.255.255.224
C. 255.255.255.240
D. 255.255.255.248 | | 2 |
| Choose three reasons why the networking industry uses a layered
model:
A.) It facilitates systematic troubleshooting
B.) It allows changes in one layer to occur without changing
other layers
C.) It allows changes to occur in all layers when changing
one protocol
D.) It clarifies how to do it rather than what general
function to be done
E.) It clarifies what general function is to be done rather
than how to
do it | | 1 |
| What is the default LMI type for Cisco Routers that are using
Frame-Relay?
A.) Gandalf5
B.) Q933A
C.) Cisco
D.) IETF
E.) ARPA
F.) SAP | | 1 |
| Inverse ARP serves what purpose?
A.) Method for a local router to introduce itself to the
remote end of
the connection
B.) Broadcast a routing table update
C.) Identify MAC addresses if the IP address is known
D.) Sent every 10 seconds used to verify the Frame Switch is
still active | | 1 |
| Which command specifies a second subinterface on serial
interface 0?
A. interface s 0.2 point-to-point
B. interface 2 s.0 point-to-point
C. suberinterface 2.s 0 point-to-point
D. interface s 0 sub 2 point-to-point
E. interface s 0.1 point-to-point sub 2 | | 1 |
| Identify the command to run 'setup'?
A.) Router(config)#setup
B.) Router?setup
C.) Router#setup
D.) Router>setup | Karrox | 1 |
| Which statement about the flow control function of TCP is true?
A. TCP makes no snarl to check for lost or duplicate data
packets
B. The application layer must sequence data packets when
using TCP
C. TCP controls the flow of UDP data through negative
acknowledgements (NAK)
D. TCP is a connection oriented protocol that acknowledges
receipt of data packets and is considered reliable | | 2 |
| Which three protocols are correctly matched to their
transport layer functions? (Choose three)
A. route selection IP
B. sliding window UDP
C. well known pods IP
D. route validation ICMP
E. connection oriented TCP
F. three-way handshake TCP
G. no sequence and acknowledgement UDP | | 1 |
| What is the Broadcast MAC Address? | Avaya | 1 |
| What would be the first command from global configuration
mode to
enable
RIP on your router for interface E0, with an address of
181.86.4.4 and
mask of 255.255.255.0 ?
A.) router rip
B.) network 181.89.4.0 255.255.255.0
C.) router rip int e0
D.) router rip 181.86.0.0
E.) router rip 181.86.4.0
F.) network 181.86.0.0 | | 1 |
| what is meant by domain ?
what is mean by DNS? | | 9 |
| Which protocol will send a message to routers if a network
outage or
congestion occurs?
A.) ARP
B.) TCP
C.) IP
D.) ICMP | | 1 |
| Which layer of the 7 layer model is responsible for representing
the application information between 2 different OS's? For
example,
converting ASCII to EBCIDIC.
A.) Transport
B.) Application
C.) Physical
D.) Session
E.) Presentation
F.) Network | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
