| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| hi friends i am jitendera kumar sinha.i have a question in
mind that what is the diffrence between router and l3 switch
i serched on google and found that switch L3 is best in lan
and router are best in wan and switch are more faster then
router.beside that any short of technical diffrence if you
body know then plz plz and plz reply.
my 2nd question is that why we canot replace router with L3
switches (donot tell that it is costly then router).i want
any technical cause.
this is 1 am hope in noon when ever i logg again i will find
the answer posted by you.
thanks onse again
plz pzl make reply
thanks
jitendera kumar sinha
jitenerasinha.it@gmail.com
| | 5 |
| Identify the components in the following command 'interface
serial0/1/1'
A.) Serial interface, port number 0, slot 1, port adapter 1
B.) Serial interface, slot 1, port number 1, port adapter 0
C.) Serial interface, slot 0, port adapter 1, port number 1 | | 1 |
| Which of the following are examples of ICMP?
A.) Traceroute
B.) Web Browsing
C.) Ping
D.) Telnet
E.) Destination Unreachable message from a router
F.) Inverse Tunnels | | 1 |
| What does the command show access-lists 101 list?
A. all defended access lists
B. all access lists within the router
C. the contents of standard access list 101
D. the contents of defended access list 101 | | 1 |
| Identify the command to disable CDP on an interface?
A.) Router(config-if)# no cdp enable
B.) Router(config-if)# no cdp run
C.) Router# no cdp enable
D.) Router(config-if)# no cdp | | 1 |
| What is the difference between OSPF Exteral Type 1 (O E1) &
External Type 2 (O E2) routes???? | | 3 |
| Choose the following that are benefits to segmenting with
router:
A.) Flow Control
B.) Manageability
C.) Multiple Active Paths
D.) Explicit packet lifetime control | | 1 |
| Which address or number is used to pass the data to the
correct application?
MAC Number
IP address
Port Number
Segment Number
| | 2 |
| Which statement is true regarding full duplex?
A.) Allows for transmission and receiving of data simultaneously
B.) Only works in a multipoint configuration
C.) Does not affect the bandwidth
D.) Allows for transmission and receiving of data but not at
the same time | | 1 |
| Which command displays the IPX SAP table?
A.) show ipx sap
B.) show sap
C.) show ipx interface
D.) show ipx servers
E.) show ipx | | 1 |
| What is the diiffernce between windows xp & windows 2000?
| VigaTech | 5 |
| Which technology is used by Catalyst switches to resolve
topology loops and ensure data flows properly through a
single network path?
A. virtual LANS (VLANS)
B. frame filtering
C. cut-through switching
D. spanning-tree protocol | | 1 |
| You want to set the console password to ralph. What would be the
first command you need to execute from global configuration
mode?
A.) line console 0
B.) enable password ralph
C.) login password ralph
D.) set password= ralph
E.) password ralph
F.) login Ralph | | 1 |
| What command can be used to test IPX connectivity?
A.) Ping 2e.000.0045.8923
B.) Ping 192.168.100.1
C.) Ping ipx 2e.0000.0045.8923
D.) Ipx ping 2e.0000.0045.8923 | | 3 |
| Define Poison Reverse?
A.) To prevent regular update messages from reinstating a
route that has
gone down
B.) Packets sent out that are not destined for a network go
to the default
network
C.) Information received on an interface cannot be sent back
out the same
interface
D.) When a network goes down, that network is advertised with an
infinite metric | | 1 |
| What is true when using DDR?
A.) HDLC is the preferred encapsulation
B.) You must use static routing
C.) You should use dynamic routing
D.) You should use ISDN | | 1 |
| Which ISDN protocol prefix specifies switching and signalling?
A.) I
B.) E
C.) Q
D.) S | | 1 |
| The Integrated Services Digital Network (ISDN) Basic Rate
Interface (BRI) provides which of the following?
A.) 1.544 Mbps
B.) 23B + 1D Channel
C.) 24B + 1D Channel
D.) 2B + 1D Channel
E.) 23B + the Disney Channel | | 2 |
| Identify the command to display the hardware platform
information?
A.) show all
B.) show platform
C.) display hardware
D.) show version | | 1 |
| What command do you enter at the keyboard to begin a user mode
session?
A.) Type 'CTRL-P'
B.) Type 'login'
C.) Just press .
D.) Type 'enable'
E.) Press 'Shift + Ctrl + 6' at the same time. | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
