| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Where is the backup configuration file stored?
A.) RAM
B.) ROM
C.) Console
D.) NVRAM | | 1 |
| Repeaters work at which layer of the OSI model?
A.) Network
B.) Session
C.) Transport
D.) Physical | | 3 |
| What are 3 ways to provide login access to router?
A.) Console
B.) TFTP
C.) Rlogin
D.) Auxiliary Port
E.) X Windows
F.) Telnet | | 1 |
| Identify the command to configure the router to boot from an IOS
located on a TFTP server?
A.) boot system tftp IOS.exe 172.16.5.1
B.) boot system tftp 172.16.5.1 IOS.exe
C.) boot system flash tftp 172.16.5.1
D.) boot system IOS.exe 172.16.5.1 | HCL | 2 |
| Identify command that configures 'Cisco1' as a secret password?
A.) Router(config)# enable secret password Cisco1
B.) Router(config)# enable secret cisco1
C.) Router(config)# enable password Cisco1
D.) Router(config)# enable secret Cisco1 | | 2 |
| What 3 sources can configuration commands be placed into RAM?
A.) HP Openview
B.) Console
C.) Vterminal
D.) TFTP server
E.) NVRAM | | 1 |
| Identify the command mode necessary to enter the standard ping
command?
A.) Router(config)#
B.) Router>
C.) Router(std-ping)#
D.) Router(config-if)# | | 1 |
| Which of the following protocols are used for logical network
addressing?
A.) IP
B.) TCP
C.) ARP
D.) ICMP
E.) RARP
F.) BootP | | 4 |
| Which three protocols are correctly matched to their
transport layer functions? (Choose three)
A. route selection IP
B. sliding window UDP
C. well known pods IP
D. route validation ICMP
E. connection oriented TCP
F. three-way handshake TCP
G. no sequence and acknowledgement UDP | | 1 |
| Which of the following are Transport layer protocols?
A.) UDP
B.) TCP
C.) NBP
D.) IP
E.) SPX | | 3 |
| You want to enable both arpa and snap encapsulation on one
router interface. How do you do this?
A. The interface can handle multiple encapsulation types
with no extra configuration.
B. Assign two network numbers, one for each encapsulation
type.
C. Enable Novell-ether to run multiple encapsulation types.
D. Both arpa and snap are enabled by default so you don't
have to configure anything. | | 1 |
| In regards to the ISDN BRI standard, which channel is used for
control?
A.) B
B.) D
C.) E
D.) I
E.) Q | | 2 |
| How does a switch use store and forward?
A.) By using a Class I repeater in a collision domain
B.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
C.) By using broadcast addresses as source addresses
D.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets | | 1 |
| Identify the administrative distance and appropriate routing
protocol?
A.) RIP = 255, IGRP = 100
B.) RIP = 100, IGRP = 120
C.) RIP = 1, IGRP = 0
D.) RIP = 120, IGRP = 100 | | 3 |
| What is true about Link-State protocols?
A.) They maintain a more complex table than distant vector
protocols
B.) They maintain a less complex table than distant vector
protocols
C.) They use routing ports
D.) The maintain backup copies of the IOS | | 1 |
| What key do you use to view the last command?
A.) Left Arrow
B.) Ctrl-P
C.) Up Arrow
D.) Right Arrow | | 2 |
| Identify the command that forces the router to load into ROM
mode
upon a reload?
A.) boot system rom
B.) rom boot
C.) boot system flash rom
D.) boot router rom | | 1 |
| Identify the following command to configure a secret password to
'cisco'?
A.) Router(config)#enable password cisco secret
B.) Router(config)#enable secret cisco
C.) Router(config)#enable secret password cisco
D.) Router(config)#set secret = cisco | | 1 |
| What is a key use of a device hardware address?
A. to obtain a vendor code / serial number from the user
B. to transmit a frame from one Interface to another Interface
C. to transmit a packet from one local device to another
local device
D. to transmit data from one local device to a remote device
across the internet
E. to contain logical information about the device to use
for end-to-end transmission | | 1 |
| Identify the type of routing protocol that exchanges entire
routing tables
at regular intervals?
A.) Link state
B.) Interior gateway protocols
C.) Appletalk routing
D.) Distance vector | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
