| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the 2 commands the saves the running-config to NVRAM?
A.) write memory
B.) copy running-config startup-config
C.) write network
D.) write backup | | 1 |
| IGRP uses flash updates, poison reverse updates, holddown
times, and split horizon. How often does it broadcast its
routing table updates?
A. 90 seconds
B. 10 seconds
C. 30 seconds
D. 45 seconds | | 1 |
| What is NOT a characteristic of a network segment on a switch?
A. The segment has its own collision domain
B. The segment can translate from one media to a different media
C. All devices in the segment are part of the same broadcast
domain
D. One device per segment can concurrently send frames to
the switch. | jetking | 1 |
| What does -1 mean in an extended IPX access-list?
A.) Any IP address
B.) Deny all
C.) Deny host
D.) Any host or any network | | 1 |
| Select the compression protocols for PPP?
A. Stac
B. Predictor
C. Quality
D. Magic Number | | 1 |
| Which statement about the Point to Point Protocol (PPP) is true?
A. PPP supports TCP/IP but not Novell IPX
B. PPP is being phased out of existence by the Serial Line
Internet Protocol (SLIP)
C. PPP providces router to router and host to network
connections over both synchronous and asynchronous circuits
D. PPP is an ITU T and ANSI standard that defines the
process for sending data over a packet switched data network
(PSDN) | | 1 |
| What is required to support full-duplex Ethernet?
A.) Multiple paths between multiple stations on a link
B.) Automatic sensing operation by all connected stations
C.) Loopback and collision detection disabled
D.) Full-duplex NIC cards | | 1 |
| Identify the command that displays traffic statistics on
serial0/1?
A.) display interface serial0/1
B.) show interface serial0/1
C.) show seria0/1 stats
D.) show interface serial0/1 stats | | 1 |
| What is the default interval for SAP updates?
A.) 60 seconds
B.) 15 seconds
C.) 30 seconds
D.) 120 seconds | | 1 |
| Identify the command to reload the router?
A.) Router(config)# reload
B.) Router# reset
C.) Router# reload
D.) Router> reload | | 1 |
| Which of the following provide correct information about a
protocol at the transport layer of the OSI model?
A.) UDP - Provides Connectionless datagrams service
B.) TCP - Provides Connection Oriented Services
C.) SMTP - Provides Mail Exchange
D.) IP - Route determination
E.) TCP - Provides Flow Control and Error Checking
F.) FTP - Transfers of Files | | 2 |
| What key do you use to view the last command?
A.) Ctrl+X
B.) Ctrl+Z
C.) Ctrl+E
D.) Ctrl+P | | 2 |
| Identify the 3 major functions at layer 3 of the OSI model?
A.) Forwarding process
B.) Logical addressing
C.) End-to-end connnections
D.) Path selection
E.) MAC address examination
F.) Network monitoring | | 2 |
| Identify the command to disable CDP on an interface?
A.) Router(config-if)# no cdp enable
B.) Router(config-if)# no cdp run
C.) Router# no cdp enable
D.) Router(config-if)# no cdp | | 1 |
| What is the extended IPX access list range?
A.) 901-1000
B.) 100-199
C.) 900-999
D.) 1000-1000 | | 1 |
| Given an IPX network with redundant paths, what command will
configure load balancing?
A.) ipx load-balance
B.) ip maximum-paths 2
C.) ipx maximum-paths 2
D.) ipx load-share | | 1 |
| what is diffrence between circit switching and packet
switching | Volvo | 1 |
| What is true about frame-relay DLCI?
A.) DLCI represents a single physical circuit
B.) DLCI is optional in all frame-relay networks
C.) DLCI identifies a logical connection between DTE devices
D.) DLCI is used to tag the beginning of a frame with VLAN
information | | 1 |
| What utility can you use to see the path a packet takes
through an
internetwork?
A.) Route
B.) SNMP
C.) Trace
D.) Ping | | 1 |
| Identify 3 methods not used to prevent routing loops?
A.) Holddown timers
B.) Sequence numbers
C.) Triggered updates
D.) Split horizon
E.) Area hierarchies
F.) Order of router startup | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
