| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| A ISDN PRI circuit can be described as which of the following?
A.) 24 B channels and 1-64Kbps D channel
B.) 23 B channels and 1-64Kbps D channel
C.) 2-D channels and 1-C channel
D.) 2-64Kbps B channels and 1-16Kbps D channel | | 1 |
| 255.255.255.128/what is the n/w id ,broadcast id and the
number of valid host(according to disco rules) | Reliance | 2 |
| How signalling can be explained in D channel of ISDN? | Tulip | 1 |
| How does the cut-through switching technique work?
A.) By using broadcast address as source addresses
B.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets
C.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
D.) By using a Class I repeater in a collision domain | | 3 |
| What is the default bandwidth of a serial connection?
A.) 1200 baud
B.) 1.544 Mbps (T1)
C.) 10 Mbps
D.) 96Kpbs | | 3 |
| Suppose we have 4 switches runing in VTP mode. So when i
create a VLAN in Server Switch this VLAN info reflect in all
other switch. So question is -
A) Suppose i m practicing this scenario in BOSON software,
When a create a VLAN in server switch n ADD ports of switch
to that VLAN, the same number of ports of client switch also
belongs to dat VLAN.
For example - In switch A (Server mode), i create a VLAN 7
name Hyderabad & port number 1, 2 & 3 put into this VLAN.
Another Switch B (Client mode), its also showing that port
number 1,2 & 3 belong the same VLAN.
How cud it possible... As we know, VTP share only VLAN
configuration information. Cud anyone explain it please....!!!!
B)Same thing, when i m practicing in PACKET TRACER 5.0, its
only showing that VLAN configuration information is shared.
No port information is shared at all. I can manually
configure individual switch port to respective VLAN as our wish.
Cud anyone explain it please..!!!
| | 3 |
| Hello Mr.Jitendera Kuamr Sinha, how is every thing going
on? Thanks for your reply. Dear Friend if you can Explain
it little bit deeper i will be realy thanks full. Wish you
all the Best.
| | 1 |
| Which of the following are characteristics of UDP?
A.) UDP is connection oriented.
B.) UDP is used with TFTP.
C.) UDP is unreliable.
D.) UDP is connectionless.
E.) UDP is at the transport layer.
F.) UDP uses no acknowledgements. | | 4 |
| Which command allows a user to see previous commands?
A.) show command
B.) CTRL-P
C.) show history
D.) CTRL-U
E.) Up Arrow
F.) SHIFT-CTRL-6 | | 1 |
| Which Standard IP Access list commands will deny only the source
address 1.1.1.1?
A.) access-list 9 deny host 1.1.1.1
B.) access-list 9 deny 1.1.1.1 255.255.255.0
C.) access-list 9 deny 1.1.1.1 0.0.0.0
D.) access-list 9 deny 1.1.1.1 0.255.255.255
E.) access-list 9 deny 1.1.1.1 255.255.255.255 | | 2 |
| Which command would configure Interface E0 with an IP address of
12.23.4.5 using a Subnet mask of 255.255.255.0 ?
A.) ip address 12.23.4.5 255.255.255.0
B.) ip address 12.23.4.5 /24
C.) ip address 12.23.4.5 mask 255.255.255.0
D.) ip address 12.23.4.5 mask ff:ff:ff:0
E.) that is an invalid mask for a class 'A' address | | 2 |
| Which is true regarding half duplex Ethernet operation?
A.) Half Duplex ethernet technology provides a transmit circuit
connection wired directly to the receiver circuit at the
other end
B.) Half duplex transmission between stations is achieved by
using point
to multipoint Ethernet and Fast Ethernet
C.) With Half Duplex transmission logically circuits feed
into a single
cable creating a situation similar to a one way bridge
D.) Half Duplex transmission between stations is achieved
using Point to
Point Ethernet & Fast Ethernet | | 1 |
| Which 2 commands shows the Cisco IOS filename?
A.) show IOS
B.) show ver
C.) show flash
D.) show mem
E.) show NVRAM | | 1 |
| Which layer defines bit synchronization?
A.) Application
B.) Network
C.) Transport
D.) Physical
E.) Session
F.) Session | | 1 |
| You have typed "ping" 172.16.101.1 and get the following
display:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echoes to 172.16.101.1,
timeout is 2 seconds:
.!!!!
What does the "." signify?
A. That one message timed out.
B. That all messages were successful.
C. That one message was successful.
D. That one message completed in under the allotted
timeframe. | | 1 |
| Which command will start the process for a Cisco IOS file image
upgrade?
A.) download
B.) copy tftp flash
C.) copy flash tftp
D.) download flash
E.) network | | 2 |
| Which of the following are valid Cisco encapsulation type names?
A.) arpa = IPX Ethernet
B.) novell-ether = IPX Ethernet_802.3
C.) snap = IEEE 802.2 SNAP on Ethernet, FDDI, and Token Ring
D.) novell-fddi = IPX Fddi_Raw
E.) sap = IEEE 802.2 on Ethernet, FDDI, and Token Ring
F.) hdlc = HDLC on serial interfaces | | 1 |
| Select the physical interfaces that PPP can be configured on
a Cisco
router:
A. Asynchronous serial
B. HSSI
C. ISDN
D. Synchronous serial | | 1 |
| Identify the command to display the status of the Frame Relay
virtual circuit?
A.) Router# show frame-relay virtual-circuit
B.) Router(config)# show frame-relay pvc
C.) Router# show frame-relay pvc
D.) Router# show virtual | | 1 |
| Identify the 2 commands that copies the configuration in
NVRAM to
RAM?
A.) copy backup-config running-config
B.) configure nvram
C.) copy startup-config running-config
D.) configure memory | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
