What is the command to manually enter a static route? A.) IP route netwo

Advertise your Business Here

Refer this Site

Login | Sign Up


	Do you have a collection of Interview Questions and interested to share with us!! Please send that collection to along with your userid / name. ThanQ

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

What is the command to manually enter a static route?

A.) IP route network

B.) IP route

C.) IP route < destination network>

D.) IP route

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: What is the command to manually enter a static route? A.) IP route network B.) IP route C.) IP route < destination network> D.) IP route

Answer
# 1

Answer: C

Is This Answer Correct ?

1 Yes

0 No

Guest

Re: What is the command to manually enter a static route? A.) IP route network B.) IP route C.) IP route < destination network> D.) IP route

Answer
# 2

b& d

Is This Answer Correct ?

1 Yes

0 No

Gopalakrishnan

Re: What is the command to manually enter a static route? A.) IP route network B.) IP route C.) IP route < destination network> D.) IP route

Answer
# 3

router(conf)#ip route <destiontion ip> <subnet mask> <exit 
interface of source ip address router (or) next hops of the 
router>.

Is This Answer Correct ?

1 Yes

0 No

Robert

Re: What is the command to manually enter a static route? A.) IP route network B.) IP route C.) IP route < destination network> D.) IP route

Answer
# 4

The answer for this question is C: IP route <destination 
network>

Is This Answer Correct ?

0 Yes

0 No

Abdi

Question	Asked @	Answers
Other CCNA Interview Questions


In regards to TCP/IP, which class of address allows for the fewest valid Internet hosts? A.) D B.) E C.) Classes are not used in TCP/IP. D.) B E.) C F.) A		1
what is frame relay.and how it is different from isdn	HCL	1
Which service takes information from multiple sources and allocates bandwidth on a single media? A. Time-division Multiplexing (TDM) B. Signaling System 7 (SS7) C. X.25 D. Frame relay		1
Which command will show you if you have a DTE or DCE cable connected to an interface?		3
Which three are typical operational phases in a basic connection oriented neloyord service? (Choose three) A. call setup B. data transfer C. load balancing D. call termination E. call priortization F. data segmentation G. data link identification		1
Which of the following is a characteristic of a switch, but not of a repeater? A.) Switches forward packets based on the IPX or IP address in the frame B.) Switches forward packets based on the IP address in the frame C.) Switches forward packets based on the MAC address in the frame D.) Switches forward packets based only on the IP address in the packet		2
Hi, I am littl bit confused about ip Addressing scheme? can someone tell me how can we assign ip addresses to pc		2
Identify 3 characteristics of a MAC address? A.) Burned into the NIC B.) 48 bits long C.) Length is 32 bits D.) Used to identify a host device E.) Contains a network portion and a host portion		2
Which OSI Reference Layer is concerned with path determination? A.) Datalink B.) Physical C.) Network D.) Transport E.) Session		2
You have OSPF traffic flooding your network via one of your router interfaces. Write the access list line that will deny all ospf traffic. Don't worry about the other lines of the access list.		1
Identify the 2 commands that will display the status and information about interface E0 only? A.) show interface ethernet E0 B.) show interface E0 C.) show E0 D.) show int E0 E.) show interface		1
What is a disadvantage of using a connection oriented protocal such as TCP? A. Packet acknowledgement may add overhead B. packets are not tagged with sequence numbers C. Loss or duplication of data packets is more likely to occur D. The application layer must assume responsibility for correct searchers of the data packets		1
What is the purpose of the DLCI? A.) Identifies the remote routers B.) Contained with a 802.2 frame for routing purposes C.) Used with PPP during authentication D.) Identifies the PVC in a Frame Relay network		1
Which three are typical operational phases in a basic connection oriented network service? A. call setup B. data transfer C. load balancing D. call termination E. caller ID F. call prionflication G. data segmentation H. data and momma I. data link identification J. callering book		1
Identify the default encapsulation on serial interfaces? A.) ISDN B.) HDLC C.) SDLC D.) Frame Relay E.) PPP		1
You just entered the following command_Router(config#) line console 0 Which operation is most likely to follow? A. Confound terminal type B. enter protocol parameters for a serial line C. create a password on the console terminal line D. establish a terminal type 4 connection to a remote host E. change from configuration mode to console privileged mode	Wipro	10
Identify the 2 commands to copy a configuration from a TFTP server to RAM? A.) configure network B.) configure overwrite C.) copy backup-config running-config D.) copy tftp running-config		1
Given the Novell IPX address 1aceb0b.0000.0c12.3456 which part is the network portion of the address? A.) 0000 B.) 1 C.) 3456 D.) 1ace E.) 0000.0c12.3456 F.) 1aceb0b		2
5. What is an advantage of using routers in your network? (Choose all that apply) A. Stops broadcast storms B. Reduces downtime on your network C. Creates internetworks D. Can filter by logical address		6
Where is the point between the customers site and the phone carrier that responsibility changes? A.) CO B.) Demarc C.) DCE D.) DTE E.) CPE		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com