| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| what is diffrence betwwen mpls and frame really | Volvo | 1 |
| In order to enable RIP, which two tasks need to be
performed? (choose two)
A. Specify the routing protocol
B. Confound static RIP routes
C. Specify directly connected subnets
D. Specify directly connected networks | | 1 |
| Which OSI layer incorporates the MAC address and the LLC?
A.) Data link
B.) Network
C.) Physcial
D.) Transport | | 3 |
| Which three basic switch functions increase available
bandwidth on the networks? (Choose three)
A. loop avoidance
B. address learning
C. hop count limiting
D. broadcast filtering
E. packet forward/filtering
F. broadcast packet hop count learning/forward/filtering | | 1 |
| When the router runs out of buffer space, this is called
________.
A. Source Quench
B. Redirect
C. Information Request
D. Low Memory | | 1 |
| Which statement about Ethernet networks is true?
A. The advantage of a full duplex is the ability to transmit
data over 111 cable
B. Full duplex Ethernet requires a point-to-point connection
when only two nodes are present
C. Ethernet switches can use full duplex mode to connect
multiple nodes to a single pod of a switch
D. Half duplex is a cut through packet processing method
that is vow fast little error correction Full duplex is a
store and forward method that is slower but has better error
correction | | 1 |
| Identify the correct IGRP configuration?
A.) Router# router igrp 100
Router# network 10.0.0.0
B.) Router(config)# router igrp 100
Router(config-router)# network 10.0.0.0
C.) Router(config)# router igrp
Router(config-router)# network 10.0.0.0 | | 1 |
| Which statements are true regarding half duplex?
A.) Only works in a point-to-point configuration
B.) Allows for transmitting and receiving but not at the
same time
C.) Allow for transmitting and receiving of data simultaneously
D.) Doubles the bandwidth | | 1 |
| Identify the command to disable CDP on an interface?
A.) Router(config-if)# no cdp enable
B.) Router(config-if)# no cdp run
C.) Router# no cdp enable
D.) Router(config-if)# no cdp | | 1 |
| 7. What is an advantage to using switches in your network?
A. Addressing of hosts by DHCP
B. Ease of administration
C. Stops broadcast storms
D. Works like a repeater
| iGate | 2 |
| Which configuration task must you complete if a remote Frame
Relay router does NOT support Inverse APP?
A.configure static maps
B.define an IP address locally
C.disable DHCP on the Frame Relay router
D.configure a static route to the remote network | | 1 |
| You want to segment a network. The network is running SNA and
Netbios. Which device should NOT be used to segment the network?
A.) A store and forward switch.
B.) A router.
C.) A Catalyst 5000.
D.) A cut-through switch.
E.) A bridge. | | 1 |
| Which ISDN specification series deals with Concepts and
Terminology?
A.) C- Series
B.) I- Series
C.) Q-Series
D.) 911-Series
E.) J-Series
F.) F-Series | | 1 |
| Identify 1 characteristic of RARP?
A.) MAC to IP address translation
B.) Connectionless delivery of packets
C.) Can be used to initiate remote O/S load sequence
D.) Generates error and control messages | | 3 |
| Identify 2 HDLC characteristics?
A.) Default serial encapsulation
B.) Open standard
C.) Supports Stacker compression
D.) Supports point-to-point and multipoint | | 1 |
| Identify the 3 characteristics of IPX RIP?
A.) Distance vector
B.) Does not support multiple paths
C.) 60 second updates
D.) Default encapsulation is SAP
E.) Uses ticks and hop count as a metric | | 1 |
| Which of the following are Distant Vector protocols?
A.) IGRP
B.) RIP
C.) OSFP
D.) EIGRP | | 1 |
| Which of the following are solutions to the problems encountered
with Distance-Vector routing?
A.) Defining a Maximum
B.) Poison Reverse
C.) Triggered Updates
D.) Shortest path first algorithm.
E.) Split Horizon | | 1 |
| What is the bandwidth capacity of one ISDN B channel
A. 64 kbps
B. 128 kbps
C. 512 kbps
D. 1.54 mkbps | | 3 |
| Which of the following is an example of the Physical Layer?
A.) TCP
B.) ARP
C.) IP
D.) FDDI
E.) LLC
F.) Fast Ethernet | | 2 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
