| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| CPE is an acronym for which of the following?
A.) Customer Premise Equipment
B.) Central Processing Engineering
C.) Customer Process Equipment
D.) Central Processing Equipment | | 1 |
| What command can be used to test IPX connectivity?
A.) Ping 2e.000.0045.8923
B.) Ping 192.168.100.1
C.) Ping ipx 2e.0000.0045.8923
D.) Ipx ping 2e.0000.0045.8923 | | 1 |
| What do the following commands accomplish?
access-list 1 permit 172.16.0.0 0.0.255.255
interface ethernet 0
IP access-group 1 out
interface ethernet 1
IP access-group 1 out
A. Only traffic from the source network 172.16.0.0 will be
blocked.
B. Only traffic from the source network 172.16.0.0 will be
forwarded.
Non-172.16.0.0 network traffic is blocked.
C. Non-172.16.0.0 traffic will be forwarded.
D. All traffic will be forwarded. | | 1 |
| What IP command would you use to test the entire IP stack?
A.) Stack-test
B.) Arp
C.) Telnet
D.) Ping
E.) Trace | | 1 |
| Which encapsulation methods are most commonly used with
dialup Integrated Services Digital Network (ISDN)?
A. IP and IPX
B. IP and PPP
C. PPP and SDLC
D. PPP and HDLC | | 1 |
| What does 'P' mean when running a Trace?
A.) Good route
B.) Protocol unreachable
C.) Source Quench
D.) Destination unreachable | | 2 |
| Identify the command to display the configured IP routing
protocols?
A.) show protocols
B.) show protocols all
C.) show routing-protocols
D.) show ip protocols | | 2 |
| What are the generic parts of a network layer address?
A. an intenetworks number and a URL
B. a vendor code and a serial number
C. a network number and a host number
D. a broadcast number and a unicast number
E. a domain identifier and a device identifier | | 1 |
| Which service uses telephone control messages and signals
between
the transfer points along the way to the called destination?
A. Signaling System 7 (SS7)
B. Time-division Multiplexing (TDM)
C. X.25
D. Frame relay | | 1 |
| A big part of the overhead on a network is broadcasts. You
divide a large number of hosts into smaller individual
networks and separate them with the proper device
According to proper networking terminology you have created
separate _______________________,
User Domains
Broadcast Domains
Collision Areas
Broadcast Areas
| | 1 |
| What is the most common layer 2 device?
A. Hub
B. Router
C. Switch
D. Repeater | Wipro | 5 |
| What is the link state routing protocol in the TCP/IP
protocol stack?
A. IP
B. IS-IS
C. NLSP
D. OSPF
E. RIP version 2 | | 2 |
| Which memory component on a Cisco router contains the
dynamic system configuration?
ROM
NVRAM
Flash
RAM/DRAM | HCL | 16 |
| Identify the keystroke used to terminate the setup mode?
A.) Ctrl-K
B.) Crtl-C
C.) Ctrl-Z
D.) Crtl-End | | 1 |
| You need to come up with a TCP/IP addressing scheme for your
company. How many network IDs must you allow for when you
define the
subnet mask for the network?
A.) One for each WAN link
B.) One for each router interface
C.) One for each NIC installed in each client
D.) One for each subnet with hosts
E.) One for each host ID | | 1 |
| The -- terminal no editing -- command will perform what
function?
A.) Edit the contents of NVRAM
B.) Allows access to the terminal port
C.) Stops the advanced editing feature
D.) Enable password functions | | 1 |
| What is masking? why is needed? | | 4 |
| There is an emergency fall-back 'skeleton' IOS stored in
read only
memory on all Cisco routers. What command would make the
router load the
IOS from
Read Only Memory?
A.) reload rom
B.) boot system rom
C.) load ios bootflash
D.) load ios rom
E.) bootsystem skeleton | | 2 |
| Identify the X.25 addressing standard?
A.) X.121
B.) X.25a
C.) ITU-1
D.) Q933a | | 1 |
| What is the default encapsulation of Netware 3.12?
A.) Ethernet_II
B.) 802.5
C.) 802.2
D.) 802.3 | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
