| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify 3 UDP characteristics?
A.) Reliable communication protocol
B.) Applications that use UDP must incorporate reliability
C.) Connnection-less oriented
D.) Incorporates no handshaking | | 2 |
| Which line from a show spantree 1 command output indicates
that virtual LAN 1 (VLAN1) is functioning properly?
A. Root pod is FastEthernet 0/26
B. Port Ethernet 0/1 of VLAN1 is Forwarding
C. Designated port is Ethernet 0/1, path cost 10
D. Designated root has priority 0 address 00D0 588F B600
E. VLAN1 is executing the IEEE compatible Spanning Tree Protocol | | 1 |
| You are conferring a Frame Relay router with subinterfaces
on interface Serial 0 Which subinterfaces numbers could you
use for this configuration?
A. 1 and 2
B. 0 2 and 0 3
C. 1 0 and 1 1
D. 0 1 a and 0 1 | | 1 |
| What is the last step in data encapsulation?
A.) User information is converted into data.
B.) Segments are converted into datagrams and packets.
C.) Frames are put into bits.
D.) Data is converted into segments.
E.) Packets are put into logical frame. | | 1 |
| The benefits to segmenting with Bridges are which of the
following?
A.) Scalability
B.) Datagram filtering
C.) Manageability
D.) Reliability | | 1 |
| Which protocol works at the Internet layer and is
responsible for
making routing decisions?
A.) UDP
B.) IP
C.) TCP
D.) ARP | | 2 |
| There are two processes to pair MAC address with IP
addresses. Which process finds an IP address from a MAC
address?
A. RARP
B. ARP
C. RIP
D. IGRP | | 2 |
| What is the juncture at which the CPE ends and the local loop
portion of the service begins?
A. Demarc
B. CO
C. Local loop
D. Last-mile | | 1 |
| When you issue the command show version your router returns
"Configuration register is 0x0101" From where does the
router boot?
A. ROM
B. NVRAM
C. Flash
D. a TFTP server | | 1 |
| What is the first step in data encapsulation?
A.) User information is converted into data.
B.) Frames are put into bits.
C.) Data is converted into segments.
D.) Segments are converted into datagrams and packets.
E.) Packets are put into logical frame. | | 1 |
| Identify the purpose of ARP?
A.) Avoiding routing loops
B.) Determining a workstation's IP address
C.) Sending a directed broadcast
D.) Determining a workstation's MAC address | | 3 |
| What is BGP attribute & How many types of attributes are
used by BGP??? | Hathway | 3 |
| What does the IPX maximum-path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| You are logged into a router, what command would
show you the IP addresses of routers connected to you?
A. show cdp neighbors detail
B. show run
C. show neighbors
D. show cdp | | 2 |
| What is an advantage of local area network (LAN) segmentation?
A. smaller collision domains
B. elimination of broadcasts
C. decreased cost of implementation
D. larger number of users within the same domain | | 1 |
| What not a name of an ISP?
A. MSN
B. Comcast
C. Verizon
D. McDonalds | | 1 |
| What is Cisco's default encapsulation method on serial
interfaces?
A.) ANSI
B.) Cisco
C.) Q933a
D.) HDLC | | 1 |
| Which of the following is true?
A. The default is to send debug output to the console screen.
B. To view debug output from a telnet session, the "terminal
monitor" command must be used
C. If the "logging buffered" command is used, the debug
output would be sent to RAM and can be viewed with the "show
log" command
D. If the "no console loggin" command were configured,
output would besent to a telnet session
E. All of the above
F. None of the above
G. A, B, and C.
H. A, C, D, and E. | | 2 |
| How do you find the parameters that you can use with the SHOW
command?
A.) ? show
B.) show ?
C.) debug show
D.) help
E.) sh? | | 1 |
| What should be the first command to create an access-list that
prevents all users on subnetwork 10.10.128.0, using subnet mask
255.255.192.0, from being able to telnet anywhere?
A.) access-list 101 deny tcp 10.10.128.0 0.0.63.255 any eq
telnet
B.) access-list 101 deny tcp 10.10.128.0 255.255.0.0 any eq
telnet
C.) access-list 101 deny tcp 10.10.128.0 255.255.192.0 any
eq telnet
D.) access-list 101 deny tcp 10.10.128.0 0.0.192.255 any eq
telnet
E.) access-list 101 deny tcp 10.10.128.0 0.0.128.255 any eq
telnet
F.) access-list 101 deny tcp 10.10.128.0 0.0.127.255 any eq
telnet | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
