| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify 2 characteristics of PPP?
A.) Uses LLC to establish the link
B.) Default serial encapsulation
C.) Support multiple layer 3 protocols
D.) Offers two types of authentication; PAP and CHAP | | 1 |
| Which protocol is used for booting diskless workstations?
A.) IP
B.) ARP
C.) RARP
D.) TCP
E.) SNMP | | 1 |
| Given the following IP address from the Class B address
range 172.35.21.12. Your network plan requires no more than
126 hosts on a shored. Which value should you use as the
subnet mask?
A. 255.255.0.0
B. 255.255.128.0
C. 255.255.126.0
D. 255.255.255.128
E. 255.255.255.252 | | 3 |
| Hi, I have packet tracer 5.0. I want to test intervlan
routing routing. Can someone plz tell me about intervlan
routing? | | 1 |
| Identify 2 transport layer protocols?
A.) IP
B.) TCP
C.) CDP
D.) ARP
E.) UDP | | 1 |
| Identify 3 UDP characteristics?
A.) Reliable communication protocol
B.) Applications that use UDP must incorporate reliability
C.) Connection-less oriented
D.) Incorporates no handshaking | | 2 |
| What are the two primary operating modes for frame switching?
A. Full Duplex
B. Half-Duplex
C. CSMA/CD
D. Cut-through
E. Fragmentation
F. Store and Forward
G. User mode
H. Privileged mode | | 1 |
| Which of the following would be displayed by the command
'SHOW CDP
NEIGHBOR DETAIL'?
A.) The incoming/outgoing port.
B.) The hardware platform.
C.) One address per protocol.
D.) Amount of Flash Memory Available
E.) The routers hostname.
F.) The subnet mask, if IP is configured. | | 1 |
| Hi,
I am littl bit confused about ip Addressing scheme? can
someone tell me how can we assign ip addresses to pc | | 2 |
| Which ISDN protocol prefix specifies switching and signaling?
A.) I
B.) E
C.) Q
D.) S | | 1 |
| Identify the 3 Internet layer IP protocols?
A.) NetBios
B.) IPX
C.) ARP
D.) IP
E.) RARP | | 1 |
| Identify the switching method that examines the destination MAC
address as the frame is being received then begins
forwarding the frame
prior to receiving the entire frame?
A.) Fragment-free
B.) Store and Forward
C.) Cut-through
D.) Fast forward | | 1 |
| What are the Timer of RIP, IGRP, EIGRP and OSPF Routing
Protocol? | | 1 |
| Which global configuration command will tell the router to load
the IOS file 'IOS_filename' from the Network File server at
1.2.3.4
during the next boot?
A.) boot system flash IOS_filename 1.2.3.4
B.) boot system tftp IOS_filename 1.2.3.4
C.) config-register 0x0 1.2.3.4
D.) boot system rom 1.2.3.4
E.) This can not be done, only the first file in flash can
be used. | | 1 |
| Which layer is responsible for putting 1s and 0s into a logical
group?
A.) Session
B.) Application
C.) Transport
D.) Data Link
E.) Physical
F.) Network | | 1 |
| The Cisco IOS is stored where?
A.) ROM
B.) CD
C.) Flash
D.) NVRAM | | 1 |
| What is the difference between OSPF Exteral Type 1 (O E1) &
External Type 2 (O E2) routes???? | | 3 |
| What command can you type to view the connections after
telneting
into multiple routers simultaneously?
A.) sh users
B.) sh ports
C.) sh host
D.) sh sessions | | 1 |
| I want to configure a serial interface on a 7500 with a VIP
card.
What global config command would give me access to a serial
interface on
a 7500?
A.) int 1/0/0
B.) int s 1/0/0
C.) int s 1/1
D.) int s0.1
E.) int s1 | | 1 |
| Which type of switching is considered to be 'wire speed?'
A.) Cut-Through
B.) Multiplexed
C.) Inverted
D.) Layer 4
E.) Store and Forward
F.) Layer 3 | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
