| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What are two ways IPX supports multiple logical networks on
an individual underrate? (Choose two)
A. network number
B. routing protocol
C. encapsulation type
D. autonomous system number | | 1 |
| Identify command that configures 'Cisco1' as a secret password?
A.) Router(config)# enable secret password Cisco1
B.) Router(config)# enable secret cisco1
C.) Router(config)# enable password Cisco1
D.) Router(config)# enable secret Cisco1 | | 2 |
| hi friends i am jitendera kumar sinha.i have a question in
mind that what is the diffrence between router and l3 switch
i serched on google and found that switch L3 is best in lan
and router are best in wan and switch are more faster then
router.beside that any short of technical diffrence if you
body know then plz plz and plz reply.
my 2nd question is that why we canot replace router with L3
switches (donot tell that it is costly then router).i want
any technical cause.
this is 1 am hope in noon when ever i logg again i will find
the answer posted by you.
thanks onse again
plz pzl make reply
thanks
jitendera kumar sinha
jitenerasinha.it@gmail.com
| | 5 |
| what is the difference between a passive and active hub??
which is better ?? | | 5 |
| Which 3 statements describe default encapsulation and LMI type
configuration?
A.) There are only 4 encapsulations and 3 LMI type options
B.) The LMI type config term options
C.) In release 11.2 the LMI type is autosensed
D.) The default LMI is Cisco
E.) IETF encapsulation must be configured unless the
connecting routers
are both
Cisco | | 1 |
| 10. Which STP state populates the MAC address table but
doesn't forward data frames?
A. Blocking
B. Listening
C. Learning
D. Forwarding
| Cisco | 3 |
| 1 what is the number of telnet session in the cisco router
a 1
b 2
c 3
d 4
e 5 | | 3 |
| What is the command to start IP RIP version 1 routing on a
Cisco router?
A. show rip
B. enable rip
C. router enable
D. router rip | | 5 |
| What are the difference between IPv4 & IPv6?? Can anyone
explain more details about it..!! | HCL | 4 |
| Which three of the following are true statements about
connection-oriented
sessions?
A.) The segments delivered are acknowledged back to the
sender upon
their reception
B.) Any segments not acknowledged are retransmitted by the
receiver
C.) A manageable data flow is maintained in order to avoid
congestion,
overloading and loss of any data
D.) Segments are sequenced back into their proper order upon
arrival at
their destination | | 3 |
| what is vlan and how will you configure vlan on 3650
switch and how many valn can you create on that switch | Volvo | 3 |
| Which of the following is not a characteristic of link-state
routing protocols?
❍ A. VLSM support
❍ B. Route summarization at any bit level
❍ C. Full routing updates at regular intervals
❍ D. Discontiguous network support | | 1 |
| Which two of the following protocols are used at the
Transport layer?
A.) ARP
B.) UDP
C.) ICMP
D.) RARP
E.) TCP
F.) BootP | | 7 |
| You have a Class B network address divided into 30 subnets. You
will add 25 new subnets within the next year. You need 600
host IDs for
each subnet. Which subnet mask should you use?
A.) 255.254.0.0
B.) 255.192.0.0
C.) 255.255.252.0
D.) 255.255.248 0 | | 1 |
| Which of the following is a connectionless protocol at the
Transport layer?
A.) UDP
B.) ARP
C.) ICMP
D.) RARP
E.) IP
F.) FTP | | 4 |
| What type of Ethernet operation allows only one entity to
transmit
at a time? For example, if someone else is transmitting,
they must wait.
A.) Full-Duplex
B.) Dual-Duplex
C.) Half-Duplex
D.) Latex
E.) Quarter-Duplex
F.) Suplex | | 1 |
| Which frame has a Type field to identify the upper-layer
protocol?
A.) 802.3
B.) 802.2
C.) 802.5
D.) Ethernet_II | | 1 |
| How does the cut-through switching technique work?
A.) By using broadcast address as source addresses
B.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets
C.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
D.) By using a Class I repeater in a collision domain | | 3 |
| Which three are typical operational phases in a basic
connection oriented network service?
A. call setup
B. data transfer
C. load balancing
D. call termination
E. caller ID
F. call prionflication
G. data segmentation
H. data and momma
I. data link identification
J. callering book | | 1 |
| Your Ethernet interface currently has the IP address of
1.1.1.1/24. You would like it to have a second IP address of
2.2.2.2/24.
Which command will do that?
A.) ip address 1.1.1.1 2.2.2.2 255.255.255.0
B.) ip address 2.2.2.2 255.255.255.0 secondary
C.) ip address 2.2.2.2 255.255.255.0
D.) This cannot be done, you can only have 1 IP address per
physical
interface.
E.) ip address 2.2.2.2 /24 | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
