| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the 3 Internet layer IP protocols?
A.) NetBios
B.) IPX
C.) ARP
D.) IP
E.) RARP | | 1 |
| Which of the following are valid Cisco encapsulation type names?
A.) arpa = IPX Ethernet
B.) novell-ether = IPX Ethernet_802.3
C.) snap = IEEE 802.2 SNAP on Ethernet, FDDI, and Token Ring
D.) novell-fddi = IPX Fddi_Raw
E.) sap = IEEE 802.2 on Ethernet, FDDI, and Token Ring
F.) hdlc = HDLC on serial interfaces | | 1 |
| Which IP host address range is allowable given an IP address
of 172.37.2.56 and 12 bits of subnetting
A. 172.37.2.48 to 172.37.2.63
B. 172.37.2.48 to 172.37.2.62
C. 172.37.2.49 to 172.37.2.62
D. 172.37.2.49 to 172.37.2.63
E. 172.37.2.55 to 172.37.2.126 | | 1 |
| Identify the command that displays the SAP table?
A.) show ipx servers
B.) display SAP table
C.) display SAP's
D.) show sap table | | 1 |
| Identify 3 characteristics of an IP address?
A.) Contains a network portion and a host portion
B.) 32 bits long
C.) Unique to each network
D.) Part of the default Cisco configuration
E.) Referred to as the hardware address | | 1 |
| what is the default ad value of the interface directly
coneted to router.
as for exmaple ad value of ospf is 90 then from ehternet
the network is conected whta is difault value of that
directly conected interface.
what is the defalt ad value of bgp
whta is access llist and how many type of access list
what is vlan
what is vpn
how e congigure the router
what is mpls
these are the question skrd to me at tcs i have replyed all
ecxept the first one
| TCS | 1 |
| What is the routing metric used by IGRP?
A.) MTU, delay, bandwidth, reliability, and loading
B.) Count to infinity
C.) TTL
D.) Hop count | | 1 |
| Which address or number is used to pass the data to the
correct application?
MAC Number
IP address
Port Number
Segment Number
| | 2 |
| What is the result of segmenting a network with a router
into segments 1 and 2?
A. It increases the number of collisions
B. It decreases the number of broadcast domains
C. It connects segment 1 and broadcasts to segment 2
D. It connects segment 1 and broadcasts from genre to segment 2 | | 1 |
| Which OSI layer handles physical address, network topology?
A.) Presentation
B.) Physical
C.) Transport
D.) Application
E.) Data-Link
F.) Network | | 1 |
| WHAT IS DIFFERENCE BETWEEN FAST ETHERNET AND ETHERNET PORT? | Bank-Of-India | 5 |
| The Cisco Catalyst 5000 switch supports full duplex. How
would you
enable it on the second port of the card in slot 1?
A.) router(config-if)# duplex full
B.) router(config)# duplex full
C.) router(config-if)# set port duplex
D.) router(config)#port duplex = full
E.) router(config-if)# set port 1/2 full | | 1 |
| what is native vlan
any one explain
sooraj | | 2 |
| What is convergence time?
A.) The update time
B.) The time it takes to reload a router
C.) The time it takes for a packet to reach its destination
D.) The time is takes for all routers update their tables
after a change
takes place | | 1 |
| Identify the default encapsulation on serial interfaces?
A.) ISDN
B.) HDLC
C.) SDLC
D.) Frame Relay
E.) PPP | | 1 |
| Which layer defines bit synchronization?
A.) Application
B.) Network
C.) Transport
D.) Physical
E.) Session
F.) Session | | 1 |
| Which three pieces of CDP information about neighbours
routers are displayed on your console terminal? (Choose three)
A. neighbours router a host name
B. the neighbours router a hardware platform
C. up to one address for each protocol supported
D. up to two addresses for each protocol supported | | 1 |
| The -- terminal no editing -- command will perform what
function?
A.) Edit the contents of NVRAM
B.) Allows access to the terminal port
C.) Stops the advanced editing feature
D.) Enable password functions | | 1 |
| Identify the command to configure DLCI 100 on an interface e0?
A.) Router(config)# frame-relay local-dlci 100
B.) Router(config)# frame-relay local-dlci 100 int e0
C.) Router(config-if)# frame-relay local-dlci 100
D.) Router(config-if)# frame-relay local-dlci 100 int e0 | | 1 |
| Identify the command that configures the bandwidth to 56K?
A.) Router(config-if)# bandwidth 56000
B.) Router(config-if)# bandwidth 56k
C.) Router(config)# bandwidth 56
D.) Router(config-if)# bandwidth 56 | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
