| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| How would you configure one host name that points to two IP
addresses?
A. IP host jacob 1.0.0.5 2.0.0.8
B. IP jacob 1.0.0.5 2.0.0.8
C. IP host jacob 1.0.0.5
D. IP host duplicate "all" | | 1 |
| What does the IPX maximum path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| Which layer is responsible for negotiating data transfer syntax?
A.) Network
B.) Session
C.) Application
D.) Transport
E.) Presentation | | 1 |
| Of the following switching types, which one has the lowest
latency?
A.) Cut-through
B.) Fragment Free
C.) None
D.) Store-and-forward | | 2 |
| Identify the purpose of the Ping command?
A.) Share routing information with a neighbor router
B.) Transmit user data when buffers are full
C.) Test connectivity at layer 3
D.) Test entire protocol stack | | 1 |
| Which three statements about Frame Relay configurations
using subinterfaces is true? (Choose three)
A. Each subinterface is conferred either multipoint or point
to point
B. Any network address must be removed from the physical
interface
C. The configuration of subinterfaces is done in router
(config-if)# mode
D. Frame Relay encapsulation must be conferred on each
subinterface | | 1 |
| Company XYZ has an employee that works out of the home. The
employee runs big client server applications and must
quickly transfer large files. The company wants the best
cost/benefit on this connection. What would be the most
practical solution?
A. an ISDN Basic Rate Interface (BRI) connection to the user
at home
B. a dedicated T1 connection to the user at home
C. a dedicated Frame Relay connection to the user at home.
D. a standard 28.8 analog dialup connection to the user at home. | | 1 |
| Which command, that is used to test address configuration,
uses Time-To-Live (TTL) values to generate messages from
each router.
A. trace
B. ping
C. telnet
D. bootp | | 1 |
| What is true when creating static route?
A.) The mask parameter is optional
B.) The administrative distance is required
C.) The gateway parameter is required
D.) The administrative distance is optional | | 1 |
| Which statement about switched and routed data flows is correct?
A. Switches create a single collision domain and a single
broadcast domain. Routers provide separate collision domains
B. Switches create separate collision domains but a single
broadcast domain. Routers provide a separate broadcast domain
C. Switches create a single collision domain and separate
broadcast domains. Routers provide a separate broadcast
domain as well
D. Switches create separate collision domains and separate
broadcast domains. Routers provide separate collision domains | | 1 |
| Identify the command to configure the configuration-register?
A.) Router# config-register 0x2102
B.) Router(config)# config-register 0x2102
C.) Router(config-reg)# 0x2102
D.) Router> config-register 0x2102 | | 1 |
| Given the following IP address from the Class C address
range 192.168.21.12. Your network plan needs addresses for
28 small prkps Each office uses its own shored. The
network design specifies that you confound for five bits of
subnetting. When you confound for this in Cisco IOS
software which shored mask should you use?
A. 255.255.0.28
B. 255.255.255.0
C. 255.255.255.28
D. 255.255.255.248
E. 255.255.255.252 | | 1 |
| What do the following commands accomplish?
access-list 1 deny 172.16.4.0 0.0.0.255
access-list 1 permit any
interface ethernet 0
IP access-group 1 out
A. This will block traffic from subnet 172.16.4.0 and allow
all other
traffic.
B. This will allow traffic from subnet 172.16.4.0 and block
all other
traffic.
C. All traffic is allowed.
D. All traffic is blocked. | | 1 |
| Which command will copy the routers configuration from NVRAM
to a
Network file server?
A.) copy start tftp
B.) copy start tftp server
C.) copy tftp startup-config
D.) copy running-config tftp
E.) copy startup-config tftp | | 1 |
| Identify the 2 methods to modify the routers boot sequence?
A.) Setup program
B.) Boot system commands
C.) RXBoot
D.) Config-register | | 1 |
| Identify the OSI layer responsible for end-to-end connections?
A.) Network
B.) Transport
C.) Session
D.) Data link
E.) TCP | | 1 |
| At what layer of the OSI reference model does FRAME-RELAY
map to?
A.) Session
B.) Physical
C.) Network
D.) Presentation
E.) Transport
F.) Datalink | | 1 |
| You are a system administrator on a NetWare network, you are
running NetWare 4.11 and you cannot communicate with your
router. What is the likely problem?
A. NetWare 4.11 defaults to 802.2 encapsulation.
B. NetWare 4.11 defaults to 802.3 encapsulation
C. Cisco routers only work with NetWare 3.11.
D. NetWare 3.11 defaults to 802.2 encapsulation. | | 1 |
| Identify the command to display the hardware platform
information?
A.) show all
B.) show platform
C.) display hardware
D.) show version | | 1 |
| What is the purpose of ARP?
A.) IP to host name resolution
B.) Host name to IP address resolution
C.) Mac to IP address resolution
D.) IP to Mac address resolution | | 2 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
