| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| The following is partial output from a routing table,
identify the
2 numbers in the square brackets; '192.168.10.0 [100/1300]
via 10.1.0.1,
00:00:23, Ethernet1'
A.) 100 = metric, 1300 = administrative distance
B.) 100 = administrative distance, 1300 = hop count
C.) 100 = administrative distance, 1300 = metric
D.) 100 = hop count, 1300 = metric | | 1 |
| Which command verifies encapsulation as well as Layer 1 and
Layer 2 statistics on a router configured for Frame Relay?
A. show ip
B. show interface
C. show statistics
D. show frame-relay | | 1 |
| You have just issued the erase startup-config Command and
reloaded your router. In which mode will your router be
when you react?
A. setup
B. startup
C. user EXEC
D. userd privileged
E. global configuration | | 2 |
| Identify the IPX standard access-list number range?
A.) 600 - 699
B.) 1000 - 1099
C.) 1 - 99
D.) 100 - 199
E.) 800 - 899 | | 1 |
| Identify the hardware component used to store buffers, tables,
running-configuration etc?
A.) NVRAM
B.) ROM
C.) RAM
D.) Flash | | 1 |
| Identify the OSI layer responsible for end-to-end connections?
A.) Network
B.) Transport
C.) Session
D.) Data link
E.) TCP | | 1 |
| Identify the command to display the configured IP routing
protocols?
A.) show protocols
B.) show protocols all
C.) show routing-protocols
D.) show ip protocols | | 1 |
| What is the IP extended access list range?
A.) 1000-1099
B.) 100-199
C.) 1-99
D.) 101-200 | | 2 |
| Which statement is true regarding the user exec and privileged
exec mode?
A.) The '?' only works in Privileged exec
B.) Privileged exec is a subset of the user exec mode
C.) They both require the enable password
D.) User exec is a subset of the privileged exec mode | | 1 |
| What is the difference between OSPF Exteral Type 1 (O E1) &
External Type 2 (O E2) routes???? | | 3 |
| How does a switch use store and forward?
A.) By using a Class I repeater in a collision domain
B.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
C.) By using broadcast addresses as source addresses
D.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets | | 1 |
| Identify the type of routing protocol that exchanges entire
routing tables
at regular intervals?
A.) Link state
B.) Interior gateway protocols
C.) Appletalk routing
D.) Distance vector | | 1 |
| Identify the command to display the hardware platform
information?
A.) show all
B.) show platform
C.) display hardware
D.) show version | | 1 |
| In regards to the ISDN BRI standard, which channel is used for
control?
A.) B
B.) D
C.) E
D.) I
E.) Q | | 1 |
| Which two steps are part of the process of creating Frame
Relay subinterfaces on a point to point connection? (Choose
two)
A. configure the router to forward all broadcast packets
B. remove any network address assigned to the physical interface
C. configure the local data link connection identifier
(DICI) for the subinterfaces
D. cartoon the total committed information rate (CIP)
available among the subinterfaces | | 1 |
| Given the command 'cl?', what will it display?
A.) Syntax of the 'clock' command
B.) Syntax of the 'clear' command
C.) All commands that begin with 'cl'
D.) All commands that begin with 'c' | | 2 |
| Given the global configuration commands:
'banner motd #'
'Hello #'
When would the message be displayed?
A.) The message of the day banner shows up before login.
B.) The message of the day banner shows up during logoff.
C.) These commands are not the right syntax for MOTD.
D.) Message of the day banners are displayed upon entering
global config
mode.
E.) Message of the day banners are not possible.
F.) The message of the day would be, 'Hello #' | | 1 |
| You want to segment a network. The network is running SNA and
Netbios. Which device should NOT be used to segment the network?
A.) A store and forward switch.
B.) A router.
C.) A Catalyst 5000.
D.) A cut-through switch.
E.) A bridge. | | 1 |
| Which of the following is a valid extended IP access-list?
A.) router(config)# access-list 101 permit tcp host
172.16.30.0 any eq
21 log
B.) router# access-list 101 permit tcp host 172.16.30.0 any
eq 21 log
C.) router(config)# acess-list 101 permit any any 172.16.30.0
D.) router(config)# access-list 101 permit ip host
172.16.30.0 any eq 21
log | HCL | 2 |
| Identify the command to configure the IP address
172.16.100.5 255.255.255.0?
A.) Router(config-if)# ip address 172.16.100.5 255.255.255.0
B.) Router(config)# ip address 172.16.100.5
C.) Router# ip address 172.16.100.5 255.255.255.0
D.) Router(config)# ip address 172.16.100.5 255.255.255.0 | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
