| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the purpose of the Ping command?
A.) Share routing information with a neighbor router
B.) Transmit user data when buffers are full
C.) Test connectivity at layer 3
D.) Test entire protocol stack | | 2 |
| Identify the 2 hardware components used to manage and/or
configure
a router?
A.) Auxiliary port
B.) ROM port
C.) Management port
D.) Console port | | 1 |
| Which configuration task must you complete if a remote Frame
Relay router does NOT support Inverse APP?
A.configure static maps
B.define an IP address locally
C.disable DHCP on the Frame Relay router
D.configure a static route to the remote network | | 1 |
| At which layer of the OSI model does the ping command operate?
A. session
B. network
C. transport
D. maintenance | jetking | 3 |
| IP extended access lists use which of the following as a
basis for
permitting or denying packets?
A.) destination address
B.) all of the above
C.) protocol
D.) source address
E.) port | | 1 |
| If configuring a Cisco router to connect to a non-Cisco router
across a Frame Relay network, which encapsulation type would
you select?
A.) Q933a
B.) ISDN
C.) IETF
D.) CISCO
E.) ANSI | | 1 |
| Identify the command to display all the valid commands at the
given mode?
A.) Help all
B.) Help
C.) All commands
D.) ? | | 2 |
| What is a function of a reliable transport layer connection?
A. route selection
B. acknowledgements
C. session checkpoints
D. system authentication | | 2 |
| You have two Cisco routers setup back-to-back in a lab using
DTE/DCE
cables. To which router would you add the clockrate command?
A.) The serial port on the DCE router
B.) The Ethernet port on the DTE router
C.) The Ethernet port on the DCE router
D.) The serial port on the DTE router | | 1 |
| An user from the LAN is able to ping the default gateway of
the router and other sites in the internet. but not able to
ping only the google site, no acc list configured and no
firewall and no problem with DNS atall. What may be the
problem with router? | Satyam | 7 |
| Which of the following is an example of the Datalink Layer?
A.) LLC
B.) TCP
C.) SQL
D.) IPX
E.) Token Ring
F.) MAC | | 2 |
| Which 3 statements describe default encapsulation and LMI type
configuration?
A.) There are only four encapsulations and 3 LMI type options
B.) The LMI type config term options
C.) In release 11.3 the LMI type is autosensed
D.) The default LMI is Cisco
E.) IETF encap must be configured unless the connecting
routers are both
cisco | | 1 |
| Identify the command that displays ethernet0/1 interface status?
A.) show interface ethernet0/1
B.) show interface ethernet e0/1
C.) show interface ethernet0.1
D.) show ethernet0/1 | | 2 |
| Identify the purpose of ICMP?
A.) Avoiding routing loops
B.) Send error and control messages
C.) Transporting routing updates
D.) Collision detection | | 1 |
| Which statement about an IP network is true?
A. A broadcast source MAC address contains all zeros
B. A MAC address is part of the physical layer of the OSI model
C. MAC addresses are used by bridges to make forwarding
decisions. IP address are used by routers.
D. IP addresses allow a flat addressing scheme. MAC
addresses use a hierarchical addressing scheme. | | 1 |
| What must be true for two routers running IGRP to communicate
their routes?
A.) Same autonomous system number
B.) Connected using Ethernet only
C.) Use composite metric
D.) Configured for PPP | | 1 |
| When discussing static routes, what is the gateway parameter
used
for?
A.) Determining the dynamic route
B.) Defining the subnet
C.) Defining the Administrative Distance
D.) Determining the next hop | | 1 |
| Identify the 2 commands that display the clock rate
configured on
the serial0 interface?
A.) show serial0
B.) show interface serial0
C.) Show clock rate serial 0
D.) show controllers serial 0
E.) show running-config | | 1 |
| Identify the 3 pieces of hardware you would not install to
prevent
broadcasts?
A.) Switch
B.) Repeater
C.) Bridge
D.) Router | | 1 |
| Which two does 100BaseT use?
A.) CSMA/CD
B.) IEEE 802.5
C.) 802.3u
D.) Switching with 53-byte cells | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
