| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is Spanning Tree Protocol and how it work? I know it
is - STP is Spanning tree Protocol. It Stops the looping in
the network? How STP work? How it stop Looping in network? | | 1 |
| When using access lists, what does a Cisco router check first?
A. To see if the packet is routable or bridgeable
B. The destination address
C. The source address
D. The packet contents | | 1 |
| IP extended access lists use which of the following as a
basis for
permitting or denying packets?
A.) destination address
B.) all of the above
C.) protocol
D.) source address
E.) port | | 1 |
| Identify the command to display all the valid commands at the
given mode?
A.) Help all
B.) Help
C.) All commands
D.) ? | | 2 |
| The two sublayers of the IEEE Data Link Layer are which of the
following?
A.) Link and Logical Control
B.) Data Link and LLC
C.) Logical Link Control and Media Access Control
D.) Data Link and MAC | | 1 |
| What 2 commands verify end to end communications?
A.) Trace
B.) debug ip session
C.) Ping
D.) Route | | 1 |
| Identify the command to display the Frame Relay map table?
A.) Router# display frame-relay map
B.) Router# show frame-relay map
C.) Router(setup)# show frame-relay map
D.) Router# show map frame-relay | | 1 |
| Which OSI layer performs code conversion, code formatting and
encryption?
A.) Physical
B.) Data-Link
C.) Application
D.) Transport
E.) Presentation
F.) Network | | 1 |
| What is the function of Layer 2 Device? | | 2 |
| Identify the command that configures the bandwidth to 56K?
A.) Router(config-if)# bandwidth 56000
B.) Router(config-if)# bandwidth 56k
C.) Router(config)# bandwidth 56
D.) Router(config-if)# bandwidth 56 | | 1 |
| Identify the purpose of ICMP?
A.) Avoiding routing loops
B.) Send error and control messages
C.) Transporting routing updates
D.) Collision detection | | 1 |
| Which layer manages protocol access to the Network layer?
A.) Datalink - MAC Sublayer
B.) Datalink - LLC Sublayer
C.) Transport
D.) Session
E.) Network | | 1 |
| The CSMA/CD Ethernet IEEE committee is defines as which of the
following?
A.) 802.2
B.) 802.3
C.) 802.4
D.) 802.5 | | 1 |
| Identify the type of hardware required to connect a Token ring
network to an Ethernet network?
A.) Repeater
B.) TR-Enet
C.) Router
D.) Token Ring to Ethernet translation hub | | 1 |
| Which term describes the process in which frames from one
network system are placed inside the frames of another
network system?
A. bridging
B. tunnelling
C. data link control
D. generic routing
E. packet switching | | 1 |
| What 3 sources can configuration commands be placed into RAM?
A.) HP Openview
B.) Console
C.) Vterminal
D.) TFTP server
E.) NVRAM | | 1 |
| You create the following standard access-list
access-list 1 deny 1.1.1.1
access-list 1 deny 2.2.2.2
int e0
ip access-group 1 in
Which of the following statements are true, with regard to
traffic flowing
into E0?
A.) This will stop IP packets with a source address of
1.1.1.1 only.
B.) This will stop all IP packets.
C.) This is an invalid configuration.
D.) This will stop no IP packets.
E.) This will stop IP packets with a source address of
2.2.2.2 only.
F.) This will stop IP packets with a source address of
1.1.1.1 and 2.2.2.2. | | 1 |
| Which of the following are examples of the Session Layer?
A.) IP
B.) Netbios Names
C.) NFS
D.) Token Ring
E.) SQL
F.) RPC | | 1 |
| Which of the following would be displayed by the command
'SHOW CDP
NEIGHBOR DETAIL'?
A.) The incoming/outgoing port.
B.) The hardware platform.
C.) One address per protocol.
D.) Amount of Flash Memory Available
E.) The routers hostname.
F.) The subnet mask, if IP is configured. | | 1 |
| What is the command to allow you to type Tokyo instead of the IP
address 172.16.30.1 to access a router named Tokyo?
A.) config t, ip host Tokyo 172.16.30.1
B.) config t, ip hostname Tokyo 172.16.30.1
C.) config t, hostname Tokyo 172.16.30.1
D.) config t, ip hostname 172.16.30.1 Tokyo | | 1 |
| |
| For more CCNA Interview Questions Click Here |