| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which three basic switch functions increase available
bandwidth on the networks? (Choose three)
A. loop avoidance
B. address learning
C. hop count limiting
D. broadcast filtering
E. packet forward/filtering | | 3 |
| Which of the following describe SMTP?
A.) Used for downloading files to the router.
B.) Used for sending e-mail.
C.) Uses TCP.
D.) Uses UDP.
E.) Uses port 25.
F.) Used for managing IP devices. | | 1 |
| Which two physical interfaces support PPP? (Choose two)
A. Ethernet
B. Token Ring
C. Synchronous serial
D. Asynchronous serial | | 1 |
| What are the 2 functions of the Data Link Mac layer?
A.) Handles access to shared media
B.) Manages protocol access to the physical network medium
C.) Provides SAPs for higher level protocols
D.) Allows multiple devices to uniquely identify one another
on the data
link layer | | 1 |
| what is used for passive intercae comand
mine answer-to prevent to take update from outside | | 1 |
| What are the two most common request/reply pair with ICMP
messages when using the ping command? (Choose two)
A. echo reply
B. echo request
C. source quench
D. fragment onset
E. information redirect
F. destination reachable
G. echo control message | | 1 |
| Which statement about the Point to Point Protocol (PPP) is true?
A. PPP supports TCP/IP but not Novell IPX
B. PPP is being phased out of existence by the Serial Line
Internet Protocol (SLIP)
C. PPP providces router to router and host to network
connections over both synchronous and asynchronous circuits
D. PPP is an ITU T and ANSI standard that defines the
process for sending data over a packet switched data network
(PSDN) | | 1 |
| Identify the command to configure the configuration-register?
A.) Router# config-register 0x2102
B.) Router(config)# config-register 0x2102
C.) Router(config-reg)# 0x2102
D.) Router> config-register 0x2102 | | 1 |
| Identify the command to display the Frame Relay map table?
A.) Router# display frame-relay map
B.) Router# show frame-relay map
C.) Router(setup)# show frame-relay map
D.) Router# show map frame-relay | | 1 |
| Which two solutions are used to reduce the chance of
distance vector routing loops? (choose two)
A. split horizon
B. route poison
C. area hierarchies
D. link state algorithms | | 1 |
| You just entered the following command_Router(config#) line
console 0 Which operation is most likely to follow?
A. Confound terminal type
B. enter protocol parameters for a serial line
C. create a password on the console terminal line
D. establish a terminal type 4 connection to a remote host
E. change from configuration mode to console privileged mode | Wipro | 10 |
| Which type of switching reads in the entire frame before
forwarding it?
A.) Tabling
B.) Store-and-Forward
C.) Inverse ARP
D.) Fast Forward
E.) Cut-Through
F.) Routing | | 1 |
| mention the funtions about connection oriented and
connectionless protocol and how it works ? | | 4 |
| Hi, I have packet tracer 5.0. I want to test intervlan
routing routing. Can someone plz tell me about intervlan
routing? | | 1 |
| Which layer hides details of network dependent information from
the higher
layers by providing transparent data transfer?
A.) Transport
B.) Physical
C.) Data Link
D.) Session
E.) Application
F.) Network | | 2 |
| Which ISDN specification deals with call Setup and Teardown?
A.) Q-Series
B.) J-Series
C.) I- Series
D.) C- Series
E.) F-Series | | 1 |
| Which commands should you use to enable IGRP routing?
A. router igrp 100
Network 192.168.1.0
Network 10.0.0.0
B. router igrp 100
Network 192.168.2.0
Network 10.0.0.0
C. router igrp 100
Network 192.168.1.0 192 168.1.1
Network 10.2.0.0 10.2.1.1
D. router igrp 100
Network 192.168.1.0 255.255.255.0
Network 10.2.0.0 255.255.255.0 | | 2 |
| Which of the following is a connectionless protocol at the
Transport layer?
A.) UDP
B.) ARP
C.) ICMP
D.) RARP
E.) IP
F.) FTP | | 2 |
| What is the standard ISDN term for a native ISDN telephone?
A.) ET
B.) TE1
C.) TE2
D.) LE
E.) TA | | 1 |
| What is the default switching method for the Cisco 5000 series?
A.) Cut-through
B.) Store-and-splice
C.) Latency
D.) Store-and-forward | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
