Given the command 'cl?', what will it display? A.) Syntax of t

Advertise your Business Here

Refer this Site

Login | Sign Up


	Do you have a collection of Interview Questions and interested to share with us!! Please send that collection to along with your userid / name. ThanQ

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

Given the command 'cl?', what will it display?

A.) Syntax of the 'clock' command

B.) Syntax of the 'clear' command

C.) All commands that begin with 'cl'

D.) All commands that begin with 'c'

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: Given the command 'cl?', what will it display? A.) Syntax of the 'clock' command B.) Syntax of the 'clear' command C.) All commands that begin with 'cl' D.) All commands that begin with 'c'

Answer
# 1

Answer: C

Is This Answer Correct ?

0 Yes

0 No

Guest

Re: Given the command 'cl?', what will it display? A.) Syntax of the 'clock' command B.) Syntax of the 'clear' command C.) All commands that begin with 'cl' D.) All commands that begin with 'c'

Answer
# 2

Is This Answer Correct ?

0 Yes

0 No

Harsh Singh

Question	Asked @	Answers
Other CCNA Interview Questions


Identify the command to disable CDP on an interface? A.) Router(config-if)# no cdp enable B.) Router(config-if)# no cdp run C.) Router# no cdp enable D.) Router(config-if)# no cdp		1
Identify IPX SAP and it's purpose? A.) Sonet Access Pipe - interface to Sonet ring B.) Service Advertising Protocol - advertise services C.) Server Appletalk Protocol - appletalk directory services D.) Service Access Point - identify upper layer protocols		1
What are the 3 ways routers learn paths to destination networks? A.) Dynamic B.) Static C.) Routing tables D.) Default		1
Bridges work at what layer of the OSI model? A.) Data Link B.) Network C.) Physical D.) Application		2
Identify the 3 methods routers learn paths to destinations? A.) Dynamic routing B.) None of the above, configured by default C.) Default routes D.) Administrative distance E.) Static routes		1
Identify the hardware component that stores the backup configuration? A.) RAM B.) NVRAM C.) Flash D.) ROM		1
What must you do to test connectivity on a dial on demand routing (DDR) link? A. increase the idle Import parameter B. send interesting traffic across the link C. reboot one of the integrated services digital network (ISDN) routers D. reset the DDR integrated services digital network (ISDN) router statistics to zero	HCL	1
The network portion of an address typically represents a: A.) Router B.) Ethernet MAC address. C.) Computer D.) Host E.) Segment		2
Identify 3 features of IGRP? A.) Composite metric B.) New horizon C.) Flash (triggered) updates D.) 60-second periodic updates E.) Poison reverse		1
What is the default switching method for the Cisco 5000 series? A.) Cut-through B.) Store-and-splice C.) Latency D.) Store-and-forward		1
What do the following commands accomplish? access-list 1 deny 172.16.4.0 0.0.0.255 access-list 1 permit any interface ethernet 0 IP access-group 1 out A. This will block traffic from subnet 172.16.4.0 and allow all other traffic. B. This will allow traffic from subnet 172.16.4.0 and block all other traffic. C. All traffic is allowed. D. All traffic is blocked.		1
Which of the following is not a characteristic of link-state routing protocols? ❍ A. VLSM support ❍ B. Route summarization at any bit level ❍ C. Full routing updates at regular intervals ❍ D. Discontiguous network support		1
1 what is the number of telnet session in the cisco router a 1 b 2 c 3 d 4 e 5		3
What does the term Base refer to in 100BaseT A. cabling type B. singnal type C. 100 mode type D. spectrum used E. speed category		2
What is the default IPX Ethernet encapsulation? A.) SNAP B.) Arpa C.) 802.2 D.) Novell-Ether E.) SAP		2
Which OSI layer provides mechanical, electrical & procedural specifications for activating, maintaining physical link? A.) Presentation B.) Network C.) Application D.) Physical E.) Transport F.) Data-Link		1
Which command listed below sets the banner message when someone connects to the router? A.) message # B.) banner # C.) login banner # D.) description # E.) login description # F.) banner motd #		2
HI friends. i need a suggestion and looking towards you foryours valuable suggestion friends i have completed ccna now i want to done red het linux system admnistration and networking i am liitle bit confuse betwwen them which one is better for me for job point of view reply soon waiting for your reply		1
Identify the correct pair of Novell Ethernet encapsulation and Cisco terminology? A.) Ethernet II, Snap B.) Ethernet 802.3, Novell-Ether C.) Ethernet SNAP, Arpa D.) Ethernet 802.2, Snap		1
Identify the command that displays the SAP table? A.) show ipx servers B.) display SAP table C.) display SAP's D.) show sap table		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com