| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which command do you use to set the Secret password to
'roundwood'?
A.) enable login roundwood
B.) enable password roundwood
C.) enable privilege roundwood
D.) enable secret= roundwood
E.) enable secret login roundwood
F.) enable secret roundwood | | 1 |
| Which OSI Reference Layer controls application to application
communication?
A.) Datalink
B.) Network
C.) Transport
D.) Session
E.) Physical | | 1 |
| What is an advantage of UDP?
Low Overhead
High Overhead
Reliable
Not reliable
| | 2 |
| What is a disadvantage of using a connection oriented
protocal such as TCP?
A. Packet acknowledgement may add overhead
B. packets are not tagged with sequence numbers
C. Loss or duplication of data packets is more likely to occur
D. The application layer must assume responsibility for
correct searchers of the data packets | | 1 |
| What type of switching creates variable latency through the
switch?
A.) Cut-Through
B.) Inverted
C.) Layer 4
D.) Multiplexed
E.) Store and Forward | | 1 |
| Which of the following do not belong to the customer?
A.) CO
B.) DCE
C.) Router
D.) CPE
E.) Demarc
F.) DTE | | 1 |
| Which three basic switch functions increase available
bandwidth on the networks? (Choose three)
A. loop avoidance
B. address learning
C. hop count limiting
D. broadcast filtering
E. packet forward/filtering
F. broadcast packet hop count learning/forward/filtering | | 1 |
| what the exact definition of Ethernet.plz reply as soon
soon as possible | | 6 |
| To monitor ipx traffic on a network, what command would you use?
A. debug ipx transaction
B. show ipx traffic
C. show ipx events
D. display ipx traffic | | 2 |
| What is the most common layer 2 device?
A. Hub
B. Router
C. Switch
D. Repeater | Wipro | 5 |
| Identify the 2 methods to modify the routers boot sequence?
A.) Setup program
B.) Boot system commands
C.) RXBoot
D.) Config-register | | 1 |
| Based upon the 1st octet rule identify the range for a Class A
address?
A.) 1 - 126
B.) 192 - 223
C.) 128 - 191
D.) 1 - 191 | | 1 |
| Identify the 3 major functions at layer 3 of the OSI model?
A.) Forwarding process
B.) Logical addressing
C.) End-to-end connnections
D.) Path selection
E.) MAC address examination
F.) Network monitoring | | 2 |
| IP RIP routing is conferred on a router but not all
interfaces attach to RIP networks. What should you use to
prevent all RIP routing updates from being sent through
selecedc interfaces without using access lists?
A. passive route
B. default routes
C. passive interface
D. route update filtering | | 2 |
| What are 3 ways to provide login access to router?
A.) Console
B.) TFTP
C.) Rlogin
D.) Auxiliary Port
E.) X Windows
F.) Telnet | | 1 |
| Which NetWare protocol works on layer 3--network layer--of
the OSI model?
A. IPX
B. NCP
C. SPX
D. NetBIOS | | 1 |
| Identify the command that forces the router to load into ROM
mode
upon a reload?
A.) boot system rom
B.) rom boot
C.) boot system flash rom
D.) boot router rom | | 1 |
| The benefits to segmenting with Bridges are which of the
following?
A.) Scalability
B.) Datagram filtering
C.) Manageability
D.) Reliability | | 1 |
| Which of the following statements are true?
A.) Store and forward switching creates variable latency
through the switch
B.) Cut through switching creates variables latency through
the switch
C.) Cut through switching works at wire speed
D.) Store and forward switching works at wire speed | | 1 |
| bWhich form of PPP error detection on Cisco routers monitors
data
dropped on a link?
A. Quality
B. Magic Number
C. Error Monitor
D. Droplink | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
